0
50 amp breaker.
Wiki User
∙ 12y ago
For a 41 amp load, you would typically use a 50 amp circuit breaker. The general rule is to select a breaker size that is 125% of the continuous load amps or equal to the load amps if it is not a continuous load. In this case, 41 amps is considered a continuous load, so you would round up to the nearest available breaker size, which is 50 amps.
Add your answer:
Earn +20 pts
What's a double breaker 20 amps and 30 amps?
A double breaker is a breaker that has 2 switches on it. One of the switches is 20 amps and the other is 30 amps.
How much 1200 watts on one breaker?
Not a whole lot. Assuming that is 120 volt power, 1200 watts would be 10 amps. A standard breaker is 15 amps.
How do you find out how big your main breaker box is?
You can determine the size of your main breaker box by looking at the number of circuits it can handle. A typical residential main breaker box is usually 100 amps, 150 amps, or 200 amps. You can also check the label on your breaker box or consult with an electrician for assistance.
How can a 30 Amps fuse for a shower of 9.5KW be replace with a 40 Amps fuse on RCD trip?
If the current safety requirement is 30 amps, you can;t run if off of a larger circuit breaker. It violates NEC and is very unsafe. If the current requirement is 40 amps , it will continuously trip a 30 amp breaker because it is too small of a breaker in electrical requirement.
If an electrician have a circuit that pulls a load of 10 amps what size breaker must that circuit be protected by?
For a circuit with a load of 10 amps, a breaker of 15 amps should be used for adequate protection. It is important to choose a breaker size that is slightly higher than the load to prevent frequent tripping and ensure safety.
What's a double breaker 20 amps and 30 amps?
A double breaker is a breaker that has 2 switches on it. One of the switches is 20 amps and the other is 30 amps.
What is KA in Circuit Breaker?
KA stands for kilo-amps, or thousands of amps. Thus a 2KA breaker means it will trip when the load exceeds 2,000 amps.
If a breaker is rated for 30 amps and is 2 poles is it ok to put an appliance that draws 50 amps?
The number that is on a breaker is the amount of amperage that the breaker can deliver before it trips. This is the same regardless of how many poles the breaker is.
What is 6InA in circuit breaker?
61 nano-amps is 0.061 milliamps or 0.000061 amps
Could you use a 12gauge wire for a 25 amp breaker single pole?
No, a 12-gauge wire is typically rated for a 20 amp circuit. To safely handle a 25 amp breaker, you would need to use a 10-gauge wire. It's important to match the wire gauge to the amperage rating of the breaker to prevent overheating and potential fire hazards.
What breaker to use in a bedroom that holds up to 15 amps with 120v?
15 amp breaker.
How much 1200 watts on one breaker?
Not a whole lot. Assuming that is 120 volt power, 1200 watts would be 10 amps. A standard breaker is 15 amps.
What size circut breaker for 10-2 wire?
A #10 wire has the capacity for 30 amps. No breaker larger than 30 amps should be used to protect the circuit.
How do you find out how big your main breaker box is?
You can determine the size of your main breaker box by looking at the number of circuits it can handle. A typical residential main breaker box is usually 100 amps, 150 amps, or 200 amps. You can also check the label on your breaker box or consult with an electrician for assistance.
How can a 30 Amps fuse for a shower of 9.5KW be replace with a 40 Amps fuse on RCD trip?
If the current safety requirement is 30 amps, you can;t run if off of a larger circuit breaker. It violates NEC and is very unsafe. If the current requirement is 40 amps , it will continuously trip a 30 amp breaker because it is too small of a breaker in electrical requirement.
If an electrician have a circuit that pulls a load of 10 amps what size breaker must that circuit be protected by?
For a circuit with a load of 10 amps, a breaker of 15 amps should be used for adequate protection. It is important to choose a breaker size that is slightly higher than the load to prevent frequent tripping and ensure safety.
What is the standard to select circuit breaker?
Add up your amps to calculate your breaker size. Add up your loads (amps), divide by 0.8, and choose that size breaker. If that number does not correspond to a standard size breaker you go to the next higher standard size breaker.
