0
It could be an open neutral between the first and second receptacles. Was this setup working properly at one time? IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
If you do this work yourself, always turn off the powerat the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicator to insure the circuit is, in fact, de-energized. === ===
What else can I help you with?
What type of electric circuit connection is given to appliances in home?
The type of electric circuit connection given to appliances in homes is typically a parallel connection. This allows each appliance to operate independently without affecting others on the same circuit. If one appliance fails, it does not disrupt the flow of electricity to the others.
What is a circuit breaker with 2 switches?
A circuit breaker with 2 switches typically refers to a double-pole circuit breaker. This type of circuit breaker has two separate switches that simultaneously disconnect both the positive and negative wires of a circuit, providing complete electrical isolation. It is commonly used for appliances or devices that require a dedicated electrical connection.
Would breaker appear with breakable and breathe?
Yes, "breaker" includes the word "break" which is related to "breakable." There is no direct connection between "breathe" and "breaker."
When installing a circuit breaker do you size the breaker to correct wire size or the device its controlling?
When installing a circuit breaker, you size the breaker based on the wire size. The breaker should be matched to the ampacity of the wire to ensure proper protection against overloads and short circuits. The device being controlled by the breaker is not a determining factor in sizing the breaker.
Why do some lights go off in your house when you turn on too many appliances?
In a well designed house the lights are not connected to the same circuit as an appliance. If by going out you are saying that a breaker trips, then your appliances and lights combined are exceeding the rating of the breaker. You either need to rewire and balance the loads better or plug high current appliances into different outlets on another breaker. If you are not tripping breakers, but lights are just dimming you have a bigger problem with inadequate current supplying your house.
Can you identify the circuit breaker that controls the power supply to the kitchen appliances?
To identify the circuit breaker that controls the power supply to the kitchen appliances, locate the breaker panel in your home and look for the one labeled "kitchen appliances." Flip the switch to the off position to cut off power to the appliances.
What is the purpose of a double 50 amp breaker in an electrical circuit?
A double 50 amp breaker in an electrical circuit is used to provide increased power capacity and protect against overloading. It allows for the connection of larger appliances or equipment that require more electricity to operate safely.
How do you test a 220 volt breaker?
You will need a multimeter to check a 220 volt breaker. You should unplug appliances that go to that particular breaker. Use the multimeter at the breaker to check the voltage. If it shows 220, then the breaker is okay. If it doesn't, then the breaker is no good.
What type of electric circuit connection is given to appliances in home?
The type of electric circuit connection given to appliances in homes is typically a parallel connection. This allows each appliance to operate independently without affecting others on the same circuit. If one appliance fails, it does not disrupt the flow of electricity to the others.
What is a circuit breaker with 2 switches?
A circuit breaker with 2 switches typically refers to a double-pole circuit breaker. This type of circuit breaker has two separate switches that simultaneously disconnect both the positive and negative wires of a circuit, providing complete electrical isolation. It is commonly used for appliances or devices that require a dedicated electrical connection.
How can I intentionally trip a breaker in a safe and controlled manner?
To intentionally trip a breaker in a safe and controlled manner, you can first identify which breaker controls the circuit you want to trip. Then, turn off all devices connected to that circuit. Next, firmly push the breaker switch to the "off" position, which will trip the breaker. Finally, reset the breaker by switching it back to the "on" position once the issue is resolved.
Would breaker appear with breakable and breathe?
Yes, "breaker" includes the word "break" which is related to "breakable." There is no direct connection between "breathe" and "breaker."
How do you repair short circuit when all appliances are tested to work properly?
If the appliances all test out and are found to have no short circuits in them then the next step is to check the supply conductors that feed the appliances. This can be easily done by unplugging the appliances and turn on its circuit breaker. When voltage to the appliance circuit causes the breaker to trip. this is the circuit with a fault on it. The most likely place is at the receptacle where the appliance plugs into the power supply. Turn the circuit off at the breaker and inspect the receptacle. If it looks suspicious change it out with a new one.
When the power cuts off after switching on an appliance what do I do?
You probably popped the breaker. The appliance is drawing too much current for that circuit (or is combined with too many other appliances on that circuit). Unplug it, turn the breaker back on. Try to find a different circuit to operate it on, or move other appliances to other circuits to reduce the load. If you own your residence you might be able to hire an electrician to completely rewire that circuit with larger capacity wire and breaker and changing the outlets also. This will get expensive though. I cannot use my microwave cooker and my stand mixer at the same time, together they will trip the breaker for the kitchen outlets, but one at a time is OK. It might also be an earth fault in the appliance - As stated turn off other appliances on the same circuit (that should cancel out any over load) and test again . If the breaker drops then the appliance is the issue
What is the difference between a 100 amp breaker box and a 125 breaker box?
The amperage capacity of the main bus bars and the connection of the main breaker to the bus bars.
Why won't the GFCI circuit breaker reset?
The GFCI circuit breaker may not reset due to a faulty connection, a ground fault in the circuit, or a malfunction in the breaker itself.
Why would plugging in an AC unit in a wall receptacle cause the fuse to blow or breaker to trip?
Is the receptacle a 110 or a 220 outlet? If it's a 110, it needs to be a 220. Are there other appliances, lights, etc. wired on the same outlet? If so, you may have to re-wire so that no other appliances, lights, etc. are wired into the same breaker. Usually the larger appliances such as air conditioners, central heat systems are wired to a separate breaker or fuse.
