Wiki User
∙ 12y agoFor USA, Canada and other countries running a 60 Hz supply service.
(LIFE SAFETY WARNING! [disclaimer]
Electricity is dangerous!
You can be injured or killed!
Improper installations can cause fire, injury and death!
Check NEC Table 220.55
The minimum circuit size for ANY electric range is 40 amps.
Circuit size depends on the nameplate rating of your range!
The Authority Having Jurisdiction has final say.
ASK YOUR INSPECTOR!!
<><><>
Ok where should we start? What is the total amp draw for the range? What plug and receptacle do you need? What size wire will safely carry the total demand of the range? What is the minimum size breaker that will protect everything? Can the service box handle the extra load?
There is a reason Electricians do what they do, they don't have to use the internet ask such a basic question.
<><><>
If you had to ask this question here you need to learn more about your local wiring code re all the items you must use for a new household AC power range circuit.
Serious home fires can result from incorrectly installed new circuits.
So that the new installation is safe and legal - and complies with the terms of your home insurance policy - you must use the correct type and size of cable, the correct type of circuit breaker and the correct type of wall outlet.
From the local wiring code, a licensed electrician will know which size of wire to use because the answer depends both on the current to be carried (amps) and on the length of the run from the breakers on the main supply panel to the place where the outlet for the kitchen range is to be fixed.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Wiki User
∙ 12y agoFor a standard electric range with standard elements, you would typically use a 40-50 amp circuit breaker and 8-gauge wire for a 240V installation. Check the manufacturer's specifications to ensure you are using the correct size breaker and wire for your specific electric range model.
Wiki User
∙ 14y agoFrom a 40 amp breaker, standard ranges have a three conductor #8 copper wire installed, terminating in a three pole four wire grounding receptacle. NEMA number 14-50R. Usually a 50 amp double throw breaker will do with 6 gauge wire
For a 120-volt appliance, a single-pole breaker with a rating suitable for the appliance's power requirements should be installed in the electric box. The amperage rating of the breaker should match the current draw of the appliance to ensure proper protection and operation. It is important to consult with a qualified electrician to determine the appropriate breaker size for your specific appliance.
A switch, circuit breaker, fuse, or switching transistor can do that.
If you don't have a Westinghouse breaker, you should use a breaker that is compatible with your electrical panel. Consult the panel's specifications or a qualified electrician to determine the appropriate replacement breaker for your specific panel. Using an incompatible breaker can be dangerous and may violate electrical codes.
You can use a 20-amp single pole breaker for 12-2 wire. This is the standard size breaker for 12-gauge wire in residential applications.
Yes, you can use a 15 amp 115 volt device in a standard outlet, as most standard outlets in the US are rated for 15 amps at 120 volts. However, it's always important to check that your device's electrical requirements match the outlet's specifications to ensure safe operation.
They should not be on the same breaker. Micro should be on a 20 amp. Oven should be on a 30 amp by its self.
Your main breaker should tell you the amps of your panel.
For a 120-volt appliance, a single-pole breaker with a rating suitable for the appliance's power requirements should be installed in the electric box. The amperage rating of the breaker should match the current draw of the appliance to ensure proper protection and operation. It is important to consult with a qualified electrician to determine the appropriate breaker size for your specific appliance.
A switch, circuit breaker, fuse, or switching transistor can do that.
Probably a wire shorted out. Probably in a junction box. This should be looked at quickly. If this is the case, the breaker or a fuse in the fuse panel should have tripped. Do not just reset the breaker or fuse as this may cause a fire.
Typical residential electric dryers are on 30 amp circuits, which means 10 gage copper wire. The circuit breaker should match the dryer cord rating, generally 30 amps.
If you don't have a Westinghouse breaker, you should use a breaker that is compatible with your electrical panel. Consult the panel's specifications or a qualified electrician to determine the appropriate replacement breaker for your specific panel. Using an incompatible breaker can be dangerous and may violate electrical codes.
You can use a 20-amp single pole breaker for 12-2 wire. This is the standard size breaker for 12-gauge wire in residential applications.
If you dont know how, you should hire an electrician, because you need to measure at breaker box, dont try if you had to come here to ask
It depends on what else you are running in the house. Add up your amperage to see if it is more than the 125amp rating. Which should be below 105 amps constant to keep from overheating the main breaker. If you are not running a big central ac system or a electric oven and water heater you should have no problem running the hot tub.
Yes, you can use a 15 amp 115 volt device in a standard outlet, as most standard outlets in the US are rated for 15 amps at 120 volts. However, it's always important to check that your device's electrical requirements match the outlet's specifications to ensure safe operation.
Branch circuits are protected by the circuit breaker found in the electrical panel. Each circuit should have its one breaker. The breaker should be rated to protect the insulation of the wire, so you can determine the breaker size based on the circuit conductor size Example #14-2 should be protected by a 15 amp breaker