0
What else can I help you with?
Can a 200A 240V house panel be fed by number 2 conductors from a service entrance meter panel with 200A main breaker?
No, number 2 conductors are not sufficient to carry 200A. You would need larger gauge wires to safely handle that amount of current. It is important to match the wire size to the amperage rating of the panel to prevent overheating and potential hazards.
What size service conductors do you need for a single phase 600 amp commercial panel?
The size of wire for service entrance conductors for a 400 amp 3 phase service could be 500 MCM copper. This is very large size wire and difficult to bend and shape, to connect to terminals in the main disconnect and distribution panel. This problem is solved by using parallel conductors or on higher ampacities triple conductors. Using parallel conductors the wire size would be three ought (3/0) copper.
How would you extend underground wire to your panel currently aluminum wire run to panel about 300ft I need to extend this to a new shop with a 100 amp panel 50 extra feet?
This is not a job for an amateur, but I will help you with some primary considerations. My answers are based on the United States' NEC (code) and do not take into consideration any local requirements. You do not want to extend your existing service conductors. You want to install a 100amp breaker into your existing panel and run conductors from there to your new panel. If this is a residential application you can run this with #4 copper conductors. If this is a commercial application you must run #3 copper conductors. I would answer this question based on what your shop is intended to do. If you are running professional equipment and are more or less "in business", use the commercial requirements. If you know how to properly ground a new service, and if your new panel has a main breaker, you can do what you need with 3 conductors. This will allow you to put neutral and ground conductors on the ground bar like you would in your primary panel. If you do not know how to properly ground a new service or doing so is not practical, you will need 4 conductors and your grounds and neutrals will have to be ISOLATED from each other in the new panel. Your neutral bar in this case would be insulated from the panel. In this case your new panel would become a sub-panel of the primary panel. Some panels do not have a main breaker and this is a critical consideration if you intend to wire it as a new service. Personally, I wouldn't install a panel without a main breaker whether or not it is a service or sub-panel.
A 60 amp electrical service panel at a 2800 square foot home would be?
If it was preinstalled, it may have been adequate at the time of installation. It depends on the power requirements of the home. If this is a new install, the NEC has a minimum of 100A for service equipment. To be honest, I would install 200A minimum to allow for future expansion.
How do you ground a 100 amp service panel?
In the service distribution panel there are termination points at the top of the panel. Two of the utilities "hot" conductors terminate on the main breaker. The neutral utility termination point is on a terminal block usually off to the side near the main hot terminations. It is in this neutral termination block where the system ground connects from the ground rods to the distribution panel. For a 100 amp panel the wire size will be a #6 bare copper conductor.
What size wire for 400 amp distribution panel?
For a distribution panel rated at 400 amps parallel runs of 3/0 conductors will do the job.
What size conductors are needed to run a 400 foot residential underground electric service?
Need to know what size service is going to be installed at the end of the run.
What is the recommended wire size for a 60 amp sub panel located 100 feet away?
For a 60 amp sub panel located 100 feet away, it is recommended to use a 6-gauge wire size to ensure proper electrical conductivity and safety.
Can a 200A 240V house panel be fed by number 2 conductors from a service entrance meter panel with 200A main breaker?
No, number 2 conductors are not sufficient to carry 200A. You would need larger gauge wires to safely handle that amount of current. It is important to match the wire size to the amperage rating of the panel to prevent overheating and potential hazards.
What size service conductors do you need for a single phase 600 amp commercial panel?
The size of wire for service entrance conductors for a 400 amp 3 phase service could be 500 MCM copper. This is very large size wire and difficult to bend and shape, to connect to terminals in the main disconnect and distribution panel. This problem is solved by using parallel conductors or on higher ampacities triple conductors. Using parallel conductors the wire size would be three ought (3/0) copper.
How would you extend underground wire to your panel currently aluminum wire run to panel about 300ft I need to extend this to a new shop with a 100 amp panel 50 extra feet?
This is not a job for an amateur, but I will help you with some primary considerations. My answers are based on the United States' NEC (code) and do not take into consideration any local requirements. You do not want to extend your existing service conductors. You want to install a 100amp breaker into your existing panel and run conductors from there to your new panel. If this is a residential application you can run this with #4 copper conductors. If this is a commercial application you must run #3 copper conductors. I would answer this question based on what your shop is intended to do. If you are running professional equipment and are more or less "in business", use the commercial requirements. If you know how to properly ground a new service, and if your new panel has a main breaker, you can do what you need with 3 conductors. This will allow you to put neutral and ground conductors on the ground bar like you would in your primary panel. If you do not know how to properly ground a new service or doing so is not practical, you will need 4 conductors and your grounds and neutrals will have to be ISOLATED from each other in the new panel. Your neutral bar in this case would be insulated from the panel. In this case your new panel would become a sub-panel of the primary panel. Some panels do not have a main breaker and this is a critical consideration if you intend to wire it as a new service. Personally, I wouldn't install a panel without a main breaker whether or not it is a service or sub-panel.
A 60 amp electrical service panel at a 2800 square foot home would be?
If it was preinstalled, it may have been adequate at the time of installation. It depends on the power requirements of the home. If this is a new install, the NEC has a minimum of 100A for service equipment. To be honest, I would install 200A minimum to allow for future expansion.
What gauge wire to use for direct burial for a garage that is 400 feet from your house?
Depends on the size of the sub-panel in that garage. If you are installing a 60 amp sub-panel 400 feet away from the main service panel then use AWG # 4.
What foot size is prodigy from Mindless Behavior?
his foot size is 8
What is the weight of a Masonite panel?
The weight of a Masonite panel can vary depending on its thickness and size. However, a standard 4x8 foot panel of 1/8 inch thick Masonite typically weighs around 35-40 pounds.
What size wire to run 250 feet away 60 amp sub panel?
Re Question with the voltage that you will be using.
How do you ground a 100 amp service panel?
In the service distribution panel there are termination points at the top of the panel. Two of the utilities "hot" conductors terminate on the main breaker. The neutral utility termination point is on a terminal block usually off to the side near the main hot terminations. It is in this neutral termination block where the system ground connects from the ground rods to the distribution panel. For a 100 amp panel the wire size will be a #6 bare copper conductor.
