answersLogoWhite

0

The sizing of the circuit breaker and hence the wire size to feed the pump are all dependant upon the amperage of the pump. This question can not be answered without that information.

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Natural Sciences

What size breaker should you use for a pool pump six GFCI outlets and a overhead light?

For a pool pump, six GFCI outlets, and an overhead light, you should use a 20 amp breaker to ensure safe and efficient operation. Make sure to follow local electrical codes and consult with a licensed electrician for proper installation.


Why would your pool circuit breaker go off?

Probably because you are either drawing too much current or you have a ground fault. If your ground fault breaker is tripping, or if you have a ground fault receptacle is tripping then you have too much circulating current through your neutral. There are many factors to consider there. Provide more information about what is on the pool's circuit and we can explore the options.


You have 220v wiring 2 hots 1 common from breaker box to pool wiring box Common is wired to equipment ground is that correct?

Correction - 2 hot (2 * 120) = 240 volts common - neutral U R 100% correct PS: 240 motor for pool ? hmmm, learn something everyday The cable from the breaker box to the pool should be a 3 conductor. In that 3 conductor cable there should be a bare ground wire (the ground wire is not included in a cable wire count). The pool ground should be connected to that bare wire, not the white neutral. This bare ground wire is then grounded back at the breaker panel to provide a direct path to trip the breaker in case of a short circuit. Code requires a GFCI ahead of the pool load to detect ground faults. See related links below on GFCI's


Every time you vacuum you blow the breaker in your house can you change the breaker?

Either your breaker switch needs to be changed for a heavier one, the pool equipment needs to be put on an other circuit or better still one of its own.It is best to talk to an ellectrician about the delails involved.


Is a GFCI breaker required for an electric pool heater?

I'm not positive but, as far as I know, one is required on a 120V heater but not on a 220V heater. Even if a GFCI isn't required I would install one anyway for the safety of your family and friends. These devices do work and are well worth the cost. Call a Professional... Either a GFCI outlet or a GFCI breaker, and I think I'd use the GFCI outlet because the reset on an outlet is closer to the pool than the breaker would be. But put it far enough away from the pool that you've got to get out to reset it. I think that's code; if it's not it should be.

Related Questions

What size amp circuit breaker should be used for a pool light?

The pool light is usually on a 15 amp circuit. The breaker feeding this circuit must have a GFCI rating.


Why limit the amount of electricity passing trough a circuit?

Circuits are limited for a few reasons firstly because certain size wiring can only handle so much voltage and amperage before it could fail secondly wiring heats up when more amperage is drawn through it which can create fires or burning out of the circuit most appliances draw set amount of current and amperage if you have a low amperage appliance Eg pool pump drawing 4 amps and the windings start to fail the motor can start drawing excessive amperage creating a hazard, if you had a large circuit it may never trip the breaker indicating a fault with the appliance which can cause catastrophic failure.


What size breaker should you use for a pool pump six GFCI outlets and a overhead light?

For a pool pump, six GFCI outlets, and an overhead light, you should use a 20 amp breaker to ensure safe and efficient operation. Make sure to follow local electrical codes and consult with a licensed electrician for proper installation.


Why does my pool pump keep tripping the breaker?

Your pool pump may be tripping the breaker due to an electrical overload, a faulty pump motor, or a short circuit. It is important to have a professional electrician or pool technician inspect and repair the issue to ensure safe and efficient operation of your pool pump.


Why does my pool pump breaker keep tripping?

Your pool pump breaker may keep tripping due to overloading, a short circuit, or a faulty pump motor. It is important to have a professional inspect and repair the issue to ensure safe and efficient operation of your pool pump.


How can you run a 115V outlet to your pool pump if you have 110V outlets outside?

You can run a wire from one of the outdoor outlets. 110, 115, and 120 volt circuits are pretty much interchangeable. An appliance rated for one of these will work fine on any of them. You may need to check the pump's amperage to be sure it isn't greater than the capacity of the circuit breaker. You need to check the NEC concerning pool pumps. The pump must be GFCI protected. A licensed electrician should be consulted to ensure this pool system is done correctly and for the safety of people using the pool.


Why would your pool circuit breaker go off?

Probably because you are either drawing too much current or you have a ground fault. If your ground fault breaker is tripping, or if you have a ground fault receptacle is tripping then you have too much circulating current through your neutral. There are many factors to consider there. Provide more information about what is on the pool's circuit and we can explore the options.


How do you ground a pool filter?

We have a large filter pump on our pool. When we installed the above ground pool, we put a in ground pump on it to keep it excessively clean. We had our neighbor, an electrical engineer, install a 220 v circuit breaker in a circuit box next to the pool which is also attached to the breaker in the house. Most pool installation companies feel that this is unnecessary which is what I was told when I which to a specialty electrical supply co. The part costs $250 and fortunately was installed for free. I wouldn't have it any other way. Any static or close electrical storm activity trips the breaker. Last summer, lightning stroke our tree which was 15 feet from the pool. The tree blew up but the pool pump was just fine. Hope this helps.


You have 220v wiring 2 hots 1 common from breaker box to pool wiring box Common is wired to equipment ground is that correct?

Correction - 2 hot (2 * 120) = 240 volts common - neutral U R 100% correct PS: 240 motor for pool ? hmmm, learn something everyday The cable from the breaker box to the pool should be a 3 conductor. In that 3 conductor cable there should be a bare ground wire (the ground wire is not included in a cable wire count). The pool ground should be connected to that bare wire, not the white neutral. This bare ground wire is then grounded back at the breaker panel to provide a direct path to trip the breaker in case of a short circuit. Code requires a GFCI ahead of the pool load to detect ground faults. See related links below on GFCI's


Every time you vacuum you blow the breaker in your house can you change the breaker?

Either your breaker switch needs to be changed for a heavier one, the pool equipment needs to be put on an other circuit or better still one of its own.It is best to talk to an ellectrician about the delails involved.


Breaker trips after running pool motor about 8 hours the timer was changed the receptacle was changed but you noticed a little bit of rust on the plug to the pool motor should that be changed?

Pool motor is overheating and or a short in the motor. You need a professional pool tech to troubleshoot.


Why does an inground hayward pool pump keep shutting off?

Does it run for a brief period then shut off? Could be a capacitor getting ready to fail. Could be getting hot. Is it tripping the circuit breaker?