Wiki User
∙ 14y agoBy asking this question you are probably not quite ready to take on this particular task. The correct answer to your question will depend on the distance from the breaker panel and exact location of the air conditioner unit, its voltage and its power rating.
Really, don't do this one yourself. Electricity is far too dangerous to handle if you have not been trained how to do this work. If you use the wrong size and type of cable for the job and/or put just one wire in the wrong place, you risk being killed by electrocution or you could even start a house fire.
How to do this job depends entirely on the Wiring Codes or Regulations for the locality (Town/County/State) and on the exact location of the electrical equipment you wish to be installed. If situated anywhere that is subject to water splashes, water spray, dampness or humidity - such as in any room supplied with running water pipes, like a kitchen, laundry room, bathroom, shower room, etc., or in a workshop, or garage (or anywhere outside a building in the open air, such as along an outside wall - or a pool-side area) in many places nowadays it is actually illegal to attempt to do this kind of work unless you are already a licensed electrician.
If you get any other answer here, you might attempt to do something you shouldn't be doing, and that may cost someone a shock, a home fire, or even their life.
<><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
Wiki User
∙ 14y agoFor a 20A breaker at 230V, you would typically use 12-gauge wire, which is rated for a maximum of 20 amps in residential wiring. This wire size is appropriate for powering a 230V receptacle for a 230V air conditioner. Make sure to check your local electrical codes and regulations before proceeding with the installation.
Wiki User
∙ 13y agoUse a 10 AWG wire when a circuit is to be driven by a 30 Amp breaker.
As with all home electrical projects, make certain that you understand and follow all local codes regarding any modifications that you are performing. If you have any questions, contact a qualified electrician or competent handyman, depending on state regulations.
Wiki User
∙ 14y agoA #12 copper wire with an insulation factor of 90 degrees C is rated at 20 amps.
Wiki User
∙ 19y ago10/3 with ground NM.
Wiki User
∙ 12y agoTypically 10 AWG.
Wiki User
∙ 14y ago4mm
Reading 230V between neutral and hot on a dryer receptacle indicates a problem with the wiring setup. In a properly functioning system, you should read 240V between hot wires and 120V between hot and neutral. The issue could be due to a faulty connection, break in the wiring, or incorrect wiring at the receptacle. It's crucial to address this issue promptly to avoid potential safety hazards and damage to the appliance.
To convert a 220v 3 prong outlet to a 110v 3 prong outlet, you will need to rewire the outlet and install a transformer to step down the voltage. This requires electrical expertise to ensure it is done safely and in compliance with local building codes. It's recommended to consult a licensed electrician for this type of conversion.
No bell wire is not meant to be 230V.
Converting a 120V receptacle to a 240V receptacle requires more than just changing the outlet. It involves creating a circuit that provides 240V power, which typically requires running a new wire from a 240V breaker in the electrical panel. It's important to consult with a licensed electrician to ensure the conversion is done safely and in compliance with electrical codes.
For a 15 amp 230V woodworking machine, you should use at least 10 AWG wire to handle the current. You can wire it into a 15 amp breaker with a suitable outlet, like a NEMA 6-15. However, if your woodworking machine has start-up surges or is a larger machine, you may want to consider using a 20 amp breaker and wire with 12 AWG to handle the load more comfortably.
Doesn't sound like a good idea to me.
Absolutely not.
If you know the wattage is getting pulled from a receptacle you can use simple math to do it for you. If not you need to use an Ampere meter. This i do not recommend as there would be no simple way to do without having to use loose wires and such. To calculate this take the wastage and divide it by the voltage in your socket (Usually 230V but can also be 110V in some areas). To give you an example. a 60w bulb in a 230v area would pull. 60W/230v = 0.26ampere.
maybe 10 amperes
at 230v it will use 5 to 6 amps
You would have to install a 230 volt outlet.
Reading 230V between neutral and hot on a dryer receptacle indicates a problem with the wiring setup. In a properly functioning system, you should read 240V between hot wires and 120V between hot and neutral. The issue could be due to a faulty connection, break in the wiring, or incorrect wiring at the receptacle. It's crucial to address this issue promptly to avoid potential safety hazards and damage to the appliance.
No. The amps must be 30 on each leg and the toggles must be rigged so that if one trips then both trip. It is best to buy the correct 230 V breaker at 30 amps.
To convert a 220v 3 prong outlet to a 110v 3 prong outlet, you will need to rewire the outlet and install a transformer to step down the voltage. This requires electrical expertise to ensure it is done safely and in compliance with local building codes. It's recommended to consult a licensed electrician for this type of conversion.
You will only get a secondary voltage of half of what it is supposed to be. This is a hypothetical question because a 120 volt plug (cap) will not fit into a 240 volt receptacle. The pin configurations will not align up.
it will not run
No bell wire is not meant to be 230V.