0
What else can I help you with?
What is the measure of speed in an engine?
The measure of speed in an engine is typically given in revolutions per minute (RPM). This indicates how many times the engine's crankshaft rotates within a minute. RPM is a key factor in determining the performance and power output of an engine.
What is used to measure storm surge?
Tidal gauges usually measure the storm surge.
How thermal radiation being measure?
Usually with a noncontact pyrometer.
What unit of measure would you use to measure photograph?
You use pixel to measure the quality of a photograph (although cameras usually take photos in megapixels (millions of pixels). You use bits / bytes to measure the file size of a digital photograph (although photos are usually MB (mega bytes) - millions of bytes).
What if the oil was low in your 350 the engine overheated to about 205 and a metal to metal knocking noise started when you gave it gas what are all possible problems?
Whenever you over heat an engine there will be problems. One being that all of the parts in the engine get really hot and start to either bend or warp. The knocking noise can come from your valves or anything that attaches to your valves. You should check out your piston rings and pistons. Connecting rods, journals and bearings. But it usually isn't as deep as that. So i Would start with the head and work your way down. you either spun a connecting rod bearing, or a main bearing. I would go with the main. to put it simply. rebuild the motor. don.
What is bearing clearance?
Bearing clearance is the distance between the crankshaft journal and the bearing surface. It is usually referred to as oil clearance, as that's what is occupying the space.
What causes a knocking noise from oil panIt is a 1983 cevy four wheel drive truck.?
A lower engine knock is usually a bad bearing on the crankshaft. Could be a rod bearing or a main bearing.
Show where thrust bearing is located?
The thrust bearing is located in the crankshaft journal. usually in the center main cap. Although sometimes toward the front or rear it is recognizable, the only main bearing with sides.
What is the meaning of a part of the car that is called pilot shaft?
That usually refers to the part of a standard transmission that inserts into the crankshaft pilot bearing or bushing.
Marine engineering crank shaft deflection of an new engine?
Crankshaft used to transforms the linear motion of the pistons into a rotational motion that is transmitted to the load.Piston connected with crankshaft by connecting rod.Each units of the crankshaft supported by crank bearing(usually journal bearing) In multi-cylinder engine every units piston connected with crankshaft create rotational motion according to firing order.Crank shaft alignment is necessary for smooth engine operation.
Why would an engine suddenly knock very loud and then stall out?
A loud knock is usually associated with a rod bearing. The rod connects the crankshaft to the piston. If a rod bearing went out, possibly from an oil pump going bad, it would stall out the motor.
What are the torque specs on rod bearing caps and the crankshaft main bearing caps for a 94 toyota 22-RE?
For a 1994 Toyota 22-RE engine, the torque specifications for the rod bearing caps are typically around 43 ft-lbs (58 Nm). For the crankshaft main bearing caps, the torque specification is usually about 50 ft-lbs (68 Nm). It's important to follow the proper sequence and pattern when tightening to ensure even distribution of force. Always refer to the specific service manual for your vehicle for the most accurate details.
What are some good examples of online journals?
There are various types of online journals on a variety of different topics. Online journals usually provide material for academic research. Universities are good sources of online journals.
Do men have diaries too?
Some do. They usually call them journals, though.
What is a slight engine knock after start up on a 1992 acura integra ls?
Usually a bottom end bearing problem mostly caused by lack of oil changes or high mileage on engine. You can try to replace the bearings but usually it's a temporary fix at best as there is probably crankshaft wear.
Similarities between books and journals?
Books are made to be read; journals aren't. Books are published; journals aren't. Journals are used to take notes in; books aren't. You can learn something from books; usually you can't from journals. Books can be made for enjoyment; journals aren't. (kind of--be careful with this one) Books can be made for a variety of ages; journals can't.
What is a railroad hot box detector?
A "hot box" is an overheated wheel bearing (usually due to lubrication failure). A hot box detector is any device at trackside that can measure the temperature of the bearings - usually using infrared detectors.
