answersLogoWhite

0

the ground plug should be up

User Avatar

Wiki User

∙ 14y ago
User Avatar

What else can I help you with?

Continue Learning about Natural Sciences

Is positioning the ground blade in the up position the correct way to install a three holed duplex receptacle by the electrical code?

There is no mention in the CEC as to which way a receptacle is to be positioned. The most common way is to have the ground pin in the down position. This way, if something drops on the plug (cap) when it is in the receptacle, the last pin to disconnect will be the ground pin. Some manufactures of appliances have 90 degree plugs (caps) installed on their equipment to present a low profile when in the receptacle. The ground pin in these types of caps is positioned to the top and the hot and neutral blades are below it. On connections like this the receptacle is mounted with the ground up to allow the appliance cord to drop down when it is plugged in. Still other applications will find the receptacle mounted sideways, usually in the back splash of kitchen counters when there is an absence of space to mount them vertically.


How can you wire a 110V plug outlet on a generator to stop the plug from melting?

If the plug is melting it is because of a heat build up caused by loose connections. If the plug is not a moulded plug check that the screws are tight. If it is not that, then the plug blades are not tight enough in the receptacle. Change out the receptacle on the generator. Draw a picture of the receptacle and mark where each wire goes. The best way of doing is is when you have the new receptacle take one wire off of the old receptacle and put it in the same position on the new receptacle. Having tight blade connections will prevent the plug overheating and melting.


What is a 3 way electrical outlet plug?

There no such thing as a "three way electrical plug". However, there are "switched outlets" (plugs) where the bottom "plug" of the receptacle is fed power full time and the top half is switched from a light switch. This is how you can walk into a room and switch on a lamp plugged into a wall receptacle. The switched half of the receptacle can be wired into a three way switch circuit. This would be a "three way switched receptacle". In this way, in a room with two entrances, you can walk in one door, switch on a plugged in lamp and exit by the other door and switch off the lamp from a second 3 way switch.


Why would only one plug-in work in a two plug-in outlet?

Two reasons. In older wiring or possibly new depending on the region, it was common place to split a receptacle especially in kitchens so that the top half was on one circuit and one was on the other. You may have a tripped breaker. Otherwise, the receptacle was cut to be a split receptacle and never wired that way. If you feel safe doing so, pull the receptacle out of the wall with the POWER OFF. Look at the sides where the wires are screwed down and see if the metal tab that runs between the two screw per side is still intact. If its not and you want the receptacle on a single circuit, replace the receptacle, but this time, don't cut the tab.


How do you change a 4 prong to a 3 prong plug in on stove?

Answer for USA, Canada and countries running a 60 Hertz supply service.Range receptacle three to fourLook in the back of the range receptacle box that is in the wall. The three wires coming in should have a bare ground wire in the cable set. It wasn't brought to the receptacle because there was no place for it on the three wire receptacle. If you find it back there under a screw terminal just add another short piece of wire under the screw and then connect the other end of the short wire to the new ground terminal on the new four position receptacle. The wire should be equal in size to the size of the wire that exists around the ground terminal now. If the house is so old that the range cable did not have a ground wire in it the code allows a separate green ground #10 wire to be taken from the breaker panel box to the existing range receptacle. This wire is to be bonded on each end. At the panel end to the ground buss and at the receptacle end around the ground screw at the back of the box unbroken and then to the new four position receptacle ground lug.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energizedIF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.

Related Questions

Is positioning the ground blade in the up position the correct way to install a three holed duplex receptacle by the electrical code?

There is no mention in the CEC as to which way a receptacle is to be positioned. The most common way is to have the ground pin in the down position. This way, if something drops on the plug (cap) when it is in the receptacle, the last pin to disconnect will be the ground pin. Some manufactures of appliances have 90 degree plugs (caps) installed on their equipment to present a low profile when in the receptacle. The ground pin in these types of caps is positioned to the top and the hot and neutral blades are below it. On connections like this the receptacle is mounted with the ground up to allow the appliance cord to drop down when it is plugged in. Still other applications will find the receptacle mounted sideways, usually in the back splash of kitchen counters when there is an absence of space to mount them vertically.


How can you wire a 110V plug outlet on a generator to stop the plug from melting?

If the plug is melting it is because of a heat build up caused by loose connections. If the plug is not a moulded plug check that the screws are tight. If it is not that, then the plug blades are not tight enough in the receptacle. Change out the receptacle on the generator. Draw a picture of the receptacle and mark where each wire goes. The best way of doing is is when you have the new receptacle take one wire off of the old receptacle and put it in the same position on the new receptacle. Having tight blade connections will prevent the plug overheating and melting.


What is the proper way to install blades of a receptacle up or down?

Up. ---- I'm not sure what the question is getting at. USUALLY THIS QUESTION IS ASKED WITH REGARD TO THE "GROUND" PRONG of a standard 3wire, 120 volt receptacle In the USA there are no requirements which dictate whether a receptacle outlet should be mounted with the ground UP or DOWN. In fact, it is also proper to mount the receptacle horizontally.


What is the proper way to test a receptacle?

The simplest way to test a receptacle is to use a plug-in type receptacle tester. This tester indicates either proper operation or common miswirings of the receptacle. If the receptacle is a GFCI, there is a special type of plug-in tester that has a GFCI trip button on top. This tester indicates the same things as the other one. In addition, you can press the test button to create a small ground fault, which will trip a properly operating GFCI. ---- IF YOU'RE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.If you do any work yourself, always turn off the power at the breaker box/fuse panel BEFORE you attempt to do any work and always use a meter or voltage indicator to insure the circuit is, in fact, de-energized.


What is the common way of referring to a plug and its corresponding socket as per the electrical engineering terminology?

Plug and socket, plug and socket outlet, plug and receptacle or plain plug and outlet all seem to be in common usage in the US. Plug and socket is possibly the only wording commonly used in the UK. [Plug and socket outlet sounds ok to a me, as a Brit, but we never really use that expression in the UK. Plug and outlet or plug and receptacle actually sound very strange!]


Can a 120V 20A non-locking plug be replaced with a locking-type plug of the same rating without affecting the performance of the appliance?

Change the receptacle and the plug is the best way to do this. Provided you use a properly rated plug, changing the plug type will not affect the appliance at all.


How do you tell if your electrical receptacle has the ground connected?

If you have access to a voltmeter put the test leads between the U ground hole in the receptacle and the smaller blade slot above it. If you get a voltage reading between 115 to 120 volts then your ground wire is connected. <<>> Easies way is to go to hardware store and buy an outlet checker. It is a 3-prong plug, often yellow in color, with several lights. Each light tells you if there is a wiring problem and also tells you if all is okay. This tester should be around $5.


What is a 3 way electrical outlet plug?

There no such thing as a "three way electrical plug". However, there are "switched outlets" (plugs) where the bottom "plug" of the receptacle is fed power full time and the top half is switched from a light switch. This is how you can walk into a room and switch on a lamp plugged into a wall receptacle. The switched half of the receptacle can be wired into a three way switch circuit. This would be a "three way switched receptacle". In this way, in a room with two entrances, you can walk in one door, switch on a plugged in lamp and exit by the other door and switch off the lamp from a second 3 way switch.


Why does your outlet spark when you insert a plug?

If the device you are plugging in is "live" then current tries to flow as soon as the metal prong from the plug touches metal on the receptacle. If for example you plug in a lamp that is turned off it won't spark. Turn the same light on first and plug it in and it will likely spark. What is happening is that the act of plugging something in isn't a perfect mechanical process. The metal makes contact here and there and is typically not decisive. If you position the plug straight on to the receptacle and shove it in quickly the spark will be minimized. Best way is to have the device turned off when plugging it in.


Why does new above counter receptacle trip breaker?

This happens quite often. The new counter plug is a split receptacle. There is a tie bar that has to be removed between the red wire and the black wire on the same side of the receptacle. A pair of needle nose pliers will do the job. If you look at the one that was removed you will see where it has been taken out. The way it is wired now you are shorting out the two hot wires and that is why the breaker trips.


Why would only one plug-in work in a two plug-in outlet?

Two reasons. In older wiring or possibly new depending on the region, it was common place to split a receptacle especially in kitchens so that the top half was on one circuit and one was on the other. You may have a tripped breaker. Otherwise, the receptacle was cut to be a split receptacle and never wired that way. If you feel safe doing so, pull the receptacle out of the wall with the POWER OFF. Look at the sides where the wires are screwed down and see if the metal tab that runs between the two screw per side is still intact. If its not and you want the receptacle on a single circuit, replace the receptacle, but this time, don't cut the tab.


How do you change a 4 prong to a 3 prong plug in on stove?

Answer for USA, Canada and countries running a 60 Hertz supply service.Range receptacle three to fourLook in the back of the range receptacle box that is in the wall. The three wires coming in should have a bare ground wire in the cable set. It wasn't brought to the receptacle because there was no place for it on the three wire receptacle. If you find it back there under a screw terminal just add another short piece of wire under the screw and then connect the other end of the short wire to the new ground terminal on the new four position receptacle. The wire should be equal in size to the size of the wire that exists around the ground terminal now. If the house is so old that the range cable did not have a ground wire in it the code allows a separate green ground #10 wire to be taken from the breaker panel box to the existing range receptacle. This wire is to be bonded on each end. At the panel end to the ground buss and at the receptacle end around the ground screw at the back of the box unbroken and then to the new four position receptacle ground lug.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energizedIF YOU ARE NOT REALLY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.