answersLogoWhite

0

The switch should always be on the HOT side. This way, when the switch is OFF, the light fixture is SAFE. Otherwise, you would have a HOT fixture with no clear return path when the swith is OFF -- very dangerous.

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Natural Sciences

Should neutral wire of lamp be connected to the 3amp or the 6 amp side of a canopy switch?

You should never switch the neutral wire. The neutral of the appliance should be connected directly to the neutral wire leading to the service panel neutral bar.


What happens if neutral and hot wire touch on the same pole of a light switch?

If the neutral and hot wires touch on the same pole of a light switch, it can cause a short circuit. This can result in overheating, potential damage to the electrical system, and a risk of fire. It is important to address this issue promptly by disconnecting the power and fixing the wiring.


Does the neutral wire go on the silver screw when wiring switches or outlets?

Yes, for most switches and outlets in the US, the neutral wire (typically white) connects to the silver screw. The hot wire (typically black) connects to the brass screw, and the ground wire (typically green or bare) connects to the green screw.


Is the neutral wire energized when the appliance is off?

No current flows in the circuit when the circuit is open, as in when the appliance is switched off. The voltage is on the "hot" side of the switch when it is in the open position but the neutral is not energized until the switch is closed.


The line side of a switch is the?

The line side is where the source of the voltage is connected. The load side is where the device being switched is attached. In the case of a light switch the line side would connect to the house power and the load side would be the bulb. The switch is usually inserted in the line carrying the load (or black wires). As it it common to use 12-2 wiring to run from the device being switched to a switch on the wall, the return wire can be colored white. A electrician places an identification on the wire to signal that it is a "hot wire" even though it is white. Typically the electrician will wrap the white wire with black tape for about 1 inch to indicate this. A white wire is normally considered to be neutral if it is not identified as a "hot or load wire".

Related Questions

How do you replace the neutral safety switch on a 2001 Dodge Dakota?

The neutral safety switch is located on the side of the transmission at the linkage connection. Unhook the wiring connector, Disconnect the linkage, then unbolt the switch to replace it.


How do you replace the neutral safety switch on a 2000 Honda Passport?

The switch is bolted on the side of the transmission. Remove the bolts and the wiring connector to remove the switch for replacement.


Where is the neutral safety switch on a 1973 dodge dart swinger?

Driver's side of transmission, about midway back. Has 3 round terminals that plugs into a wiring harness.


How do you replace the neutral safety switch on a 1993 GMC Suburban?

The neutral safety switch SHOULD be screwed into the side (normally drivers) of the transmission and will have 2 leads going from it.


Where is the neutral switch located on a 2001 ford ranger?

I believe the neutral safety switch is mounted on the side of your transmission


Where is the neutral safety switch on a 1992 dodge Dakota truck?

The neutral safety switch is on the side of the transmission. It screws into the side and has a small three wire plug.


Where is the backup switch on a 2002 Dodge Ram?

I don't know what engine/transmission you have, but on my wiring diagrams for the Magnum V8's / 46RE transmissions, the reverse switch is part of the Park/Neutral switch on the left side of the transmission, purple with a black stripe.


What is the location of the neutral safety switch in a 1994 Buick skylark 6-cylinder custom?

The neutral safety switch should be on the side of the transmission. It is where the linkage connects to the side.


Where is the neutral safety switch on a 1993 Nissan Sentra?

The 1993 Nissan neutral safety switch can be found on the left-hand side of the transmission. The neutral safety switch will be near the front of the transmission.


What is the recommended wiring diagram for a 60 amp disconnect switch?

The recommended wiring diagram for a 60 amp disconnect switch typically includes connecting the power source to the line side of the switch and the load to the load side of the switch. It is important to follow the manufacturer's instructions and local electrical codes when wiring the disconnect switch.


Where is the neutral switch on a 1993 Chevy Silverado?

there is a switch on the lever on the trans on the driver side


Where is the neutral safety located on a 84 cougar?

neutral safety switch is located on side of transmission