For 220v circuits
GE circuit breakers with catalog numbers ranging from THQL1115 through to THQL1150 can be substituted like for like with Cutler-Hammer circuit breakers coded CL115 through to CL150, ITE Siemens circuit breakers coded Q115 through to Q150 and Square D circuit breakers coded HOM115 through to HOM150. These are single pole breakers. GE circuit breakers with catalog codes from THQL2115 through to THQL2150 can be substituted with Cutler-Hammer circuit breakers CL215 through to CL250, Square D circuit breakers HOM215 through to HOM250 and ITE Siemens circuit breakers Q215 through to Q250 of the same amperage and voltage. These are double pole breakers.
Yes. An everyday occurrence of this circuitry is in your kitchen counter split receptacles. The top half of the receptacle is a 15 amp circuit and from the same breaker the bottom half of the receptacle is another 15 amp circuit. A two pole single handle breaker is a common trip. If one of the circuits fed from the breaker faults the other connected circuit will shut off also. If you are talking about slot position in a breaker panel, you can remove the two pole breaker and install two single pole breakers.
The term "double pole" usually means a breaker with 2 handles that attaches in the space as a normal single pole breaker. If this is what you mean, no, you cannot. There is no potential, or voltage, between the wire terminals. If by "double pole" you mean what is usually called a 2-pole breaker, which is a breaker with 2 handles that attaches in the space of 2 single pole breakers, then yes, you can use this breaker and 12/2 wire to produce a 220v circuit.
It depends on the specific requirements of your electrical system. Single pole breakers are typically used for 120-volt circuits, while double pole breakers are used for 240-volt circuits. If you are unsure, it is recommended to consult with a qualified electrician to determine the appropriate type of breaker for your needs.
No, it is not recommended to connect a 2 pole load to 2 single pole breakers as this can cause issues with proper circuit protection and may lead to electrical hazards. It is best to use a dedicated 2-pole breaker for a 2 pole load to ensure proper operation and safety.
Tandem breakers, also known as double-pole breakers, are generally safe to use in residential electrical panels as long as they are installed properly and meet the electrical code requirements. However, it is important to consult with a licensed electrician to ensure that the panel can accommodate tandem breakers without overloading the circuit.
GE circuit breakers with catalog numbers ranging from THQL1115 through to THQL1150 can be substituted like for like with Cutler-Hammer circuit breakers coded CL115 through to CL150, ITE Siemens circuit breakers coded Q115 through to Q150 and Square D circuit breakers coded HOM115 through to HOM150. These are single pole breakers. GE circuit breakers with catalog codes from THQL2115 through to THQL2150 can be substituted with Cutler-Hammer circuit breakers CL215 through to CL250, Square D circuit breakers HOM215 through to HOM250 and ITE Siemens circuit breakers Q215 through to Q250 of the same amperage and voltage. These are double pole breakers.
The appropriate double pole 30 amp breaker to use for a dryer installation is a 30 amp double pole circuit breaker.
Yes. An everyday occurrence of this circuitry is in your kitchen counter split receptacles. The top half of the receptacle is a 15 amp circuit and from the same breaker the bottom half of the receptacle is another 15 amp circuit. A two pole single handle breaker is a common trip. If one of the circuits fed from the breaker faults the other connected circuit will shut off also. If you are talking about slot position in a breaker panel, you can remove the two pole breaker and install two single pole breakers.
The term "double pole" usually means a breaker with 2 handles that attaches in the space as a normal single pole breaker. If this is what you mean, no, you cannot. There is no potential, or voltage, between the wire terminals. If by "double pole" you mean what is usually called a 2-pole breaker, which is a breaker with 2 handles that attaches in the space of 2 single pole breakers, then yes, you can use this breaker and 12/2 wire to produce a 220v circuit.
It depends on the specific requirements of your electrical system. Single pole breakers are typically used for 120-volt circuits, while double pole breakers are used for 240-volt circuits. If you are unsure, it is recommended to consult with a qualified electrician to determine the appropriate type of breaker for your needs.
No, it is not recommended to connect a 2 pole load to 2 single pole breakers as this can cause issues with proper circuit protection and may lead to electrical hazards. It is best to use a dedicated 2-pole breaker for a 2 pole load to ensure proper operation and safety.
circuit breakers ...fuses
Double pole refers to a switch that controls two separate electrical circuits, while triple pole refers to a switch that controls three separate electrical circuits. Triple pole switches are typically used for applications that require more complex wiring configurations or higher voltage control compared to double pole switches.
No, it is not safe to use two 20 amp circuit breakers to protect a 40 amp circuit. Circuit breakers are designed to protect the wiring in a circuit from overheating, and using a higher amperage circuit breaker than the wiring is rated for can lead to overheating and potential fire hazards. It is important to use the correct size circuit breaker for the amperage rating of the circuit.
You can't change the one breaker, but you can't use two separate arc fault breakers unless you separate the neutrals. However double pole arc fault breakers are made for this purpose and the common neutral would be O.K.
Yes, it is called a three wire circuit. The two circuits have to be adjacent legs in the distribution panel, they can not be on the same leg. Kitchen counter split circuits use this configuration. The circuit wiring has to be protected by a two pole breaker so that if any work is done on the circuit both legs will be disconnected when the breaker is turned off. If two single pole breakers are used in this installation there should be a common tie bar to connect the two handles of the single pole breakers together to make the job conform to the electrical code.