Could be a loose connection somewhere, or a bad switch, or a bad outlet.
You can if you have a neutral wire present. If the existing switch is what is called a "switch loop" then you can not change the existing switch to a switched outlet. You can identify a switch loop by looking at the wires coming into the switch bow. If there are only one set of wires usually a black and white and they go directly to the switch then you have a switch loop
You can attach/splice into the power feed to outlet (ways of doing this can vary with how the outlet is wired but make sure that all or part of the outlet isn't controlled by an existing switch). You can then take the hot, neutral and ground to a light fixture or to the first switch, then to the second switch. It is normally easier to do this project by taking power to the light (s) first, with 2 wire drops to the switches, from basement or attic.
If the question is, can I wire a switch to an existing light fixture (and I must assume that it's something like a pull-chain light fixture), the answer is yes.If the question is, "how do I wire a switch to an existing light fixture that has no external switch", the answer is, "in series".The attached web site gives simple instructions on how to wire a basic light switch to an existing light.See sources and related links below
Only if the existing switch box has an unswitched hot and neutral in it.
Connect the incoming power to the line side of the GFCi outlet. Now run another wire connected to the line side of the GFCI outlet from the GFCI outlet to the switches. Power one of the switches and use that switch to turn on the 2 lights. Run power from that switch to another switch and use that switch to send power to the fan. Mount both switches in a double pole switch box. If the light above the sink has an outlet on it then you will have to connect power going to that light on the load side of the GFCI outlet. If not then just connect it to the line side.
Sure. For a light you need a fixture to hold the light and the light itself. The light needs to be connected to a voltage supply which you can get from the outlet. In the outlet box you will have a black, white and bare ground wire. Essentially you connect the white and bare wires directly to the light and switch the black wire (hot) through a switch.
You can if you have a neutral wire present. If the existing switch is what is called a "switch loop" then you can not change the existing switch to a switched outlet. You can identify a switch loop by looking at the wires coming into the switch bow. If there are only one set of wires usually a black and white and they go directly to the switch then you have a switch loop
You can attach/splice into the power feed to outlet (ways of doing this can vary with how the outlet is wired but make sure that all or part of the outlet isn't controlled by an existing switch). You can then take the hot, neutral and ground to a light fixture or to the first switch, then to the second switch. It is normally easier to do this project by taking power to the light (s) first, with 2 wire drops to the switches, from basement or attic.
No.
If the question is, can I wire a switch to an existing light fixture (and I must assume that it's something like a pull-chain light fixture), the answer is yes.If the question is, "how do I wire a switch to an existing light fixture that has no external switch", the answer is, "in series".The attached web site gives simple instructions on how to wire a basic light switch to an existing light.See sources and related links below
A single pole switch controls a light or outlet at one location. A 3 way switch controls a light or outlet from 2 locations.
Change the wall outlets
It may depend on your state Electrical Code. Normally you need to mount an outlet, (bottom of outlet box) around 12 inches above the floor. It is perfectly ok to mount one below a light switch. There are different codes for bathrooms, kitchens, laundry rooms, and garages. Check your local codes to be sure.Your best bet is to check the National Electrical Code 2017 Handbook or ask Electrocution Lawyers PLLC at electrocuted.com
Only if the existing switch box has an unswitched hot and neutral in it.
An electrical cord is provided for just that purpose and when plugged into an electrical outlet, the battery charging light will come on. After the unit is fully charged, the Battery Fully Charged light comes on and you can unplug from electrical outlet and use anywhere you need it.
Connect the incoming power to the line side of the GFCi outlet. Now run another wire connected to the line side of the GFCI outlet from the GFCI outlet to the switches. Power one of the switches and use that switch to turn on the 2 lights. Run power from that switch to another switch and use that switch to send power to the fan. Mount both switches in a double pole switch box. If the light above the sink has an outlet on it then you will have to connect power going to that light on the load side of the GFCI outlet. If not then just connect it to the line side.
You need two separate switches. You can get two switches that are in the same form factor as a single switch (2 gang switch). You use one switch for the outlet and the other for the light. You switch the black wires which are "hot".