0
(LIFE SAFETY WARNING! [disclaimer]
Electricity is dangerous!
You can be injured or killed!
Improper installations can cause fire, injury and death!) The reason a poorly wired lamp [fixture] may seem to cause a receptacle to blow but have an effect on other receptacles when no GFCI or breaker tripped is that these devices are all wired in parallel [mechanically speaking] on the same circuit.
The fault current flows through the whole circuit, so every device is subjected to the same current.
1.] The circuit breaker on the main panel may be tripped, but not have an external mechanical indication. [The handle could be stuck.] Reset your breakers anyway and the circuit may reset.
2.] The breaker may have failed under the fault current and needs to be replaced.
3.] One of the splices or screw termination connections for the conductors in the circuit hs failed completely or partially under the fault current and needs to be repaired.
4.] You are possible mistaken, and there is some device in the circuit you have not recognized. <><><>
As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.
Before you do any work yourself,
on electrical circuits, equipment or appliances,
always use a test meter to ensure the circuit is, in fact, de-energized.
IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB
SAFELY AND COMPETENTLY
REFER THIS WORK TO QUALIFIED PROFESSIONALS.
What else can I help you with?
Why power circuits and lighting circuits require a separate circuit breaker?
Utility outlets and lighting outlets should be separate so that when a utilization device plugged into an outlet trips the breaker or blows the fuse, you won't be left trying to find your way to safety in the dark. Light fixtures are much less likely to trip a breaker in ordinary use, but there are places you also want more than one lighting circuit for illumination.
Why would using a small kitchen appliance trip the circuit breaker for the bedrooms and not for the outlet that it is plugged into?
Kitchen outlets are rated at 20 amps and only dedicated for the kitchen. code states that there must be two 20 amp circuits supplying kitchen small appliances. bedroom outlets are fed by a 15 amp circuit most likely and that circuit is most likely feeding two rooms or so.
When installing a circuit breaker do you size the breaker to correct wire size or the device its controlling?
When installing a circuit breaker, you size the breaker based on the wire size. The breaker should be matched to the ampacity of the wire to ensure proper protection against overloads and short circuits. The device being controlled by the breaker is not a determining factor in sizing the breaker.
What type of circuit and or breaker should a typical consumer-sold hot plate rated at around 1800w with 2 burners for 120v ac be plugged into - will typical kitchen countertop plugs do?
1800 watts will require a 20 amp circuit. Kitchen countertop outlets are usually, but not always, 20 amp circuits.
Can a garbage disposal be on the same circuit as four outlets and a ceiling fan?
Yes, if the circuit breaker and the wiring is large enough to carry the sum of the amp draw of all. Without knowing what will be plugged into the outlets, there is no way to be more specific. <<>> It is recommended to use a dedicated circuit for a garbage disposal. It is best not to add any additional loads to kitchen counter receptacles as these are also dedicated circuits.
Why won't the circuit breaker reset when nothing is plugged in?
A circuit breaker may not reset when nothing is plugged in because there could be a fault in the wiring or the breaker itself. This fault can prevent the breaker from properly detecting and resetting in the absence of any plugged-in devices.
What if your circuit breaker started tripping with no change of things plugged into an outlet Does this mean the circuit breaker needs to be replaced?
Circuit breakers can degrade over time but it would be better to get a competant electrician to do it. It might also mean you have too many things plugged into one outlet. Sometimes one circuit breaker may protect several outlets so it might be tripping because of a change in another outlet. ELECTRICTY IS DANGEROUS!!!! Don't do it yourself.
If your circuit breaker popped and will not go back what should you do?
first be sure to reset the breaker handle to the off position. When a breaker trips the handle goes to a neutral position. After resetting the handle turn it tothe on position. If it trips again there is a short in the circuit. Find out which outlets are not workingand unplug anything that is currently plugged in to the outlets. Reset the breaker and turn it to the on position,if it trips again call a qualified electrician.
Why is the circuit breaker tripping?
The circuit breaker is tripping because there is an overload of electrical current flowing through the circuit, which can be caused by too many devices plugged in or a short circuit.
Why does the circuit breaker keep tripping even when nothing is plugged in?
The circuit breaker may keep tripping even when nothing is plugged in due to a short circuit, ground fault, or overload in the electrical wiring or the circuit itself. These issues can cause the circuit breaker to trip as a safety measure to prevent overheating and potential fire hazards.
Why does the circuit breaker keep tripping even when there is nothing plugged in?
The circuit breaker may keep tripping even when nothing is plugged in due to a short circuit, ground fault, or overload in the electrical wiring or the circuit itself. These issues can cause the circuit breaker to trip as a safety measure to prevent overheating and potential fire hazards.
Why power circuits and lighting circuits require a separate circuit breaker?
Utility outlets and lighting outlets should be separate so that when a utilization device plugged into an outlet trips the breaker or blows the fuse, you won't be left trying to find your way to safety in the dark. Light fixtures are much less likely to trip a breaker in ordinary use, but there are places you also want more than one lighting circuit for illumination.
Why does my breaker keep tripping even when nothing is plugged in?
A breaker may keep tripping even when nothing is plugged in due to a short circuit, overloaded circuit, or a faulty breaker. It is important to have an electrician inspect and troubleshoot the issue to ensure safety and proper functioning of the electrical system.
How many outlets on 15 amp breaker?
As many as you want. It is the power consumed by the thing(s) plugged in that is of concern.
How can I determine what is tripping my circuit breaker?
To determine what is tripping your circuit breaker, you can unplug all devices on that circuit and then plug them back in one by one to identify the culprit. If the breaker trips when a specific device is plugged in, that device may be causing the issue.
Why would using a small kitchen appliance trip the circuit breaker for the bedrooms and not for the outlet that it is plugged into?
Kitchen outlets are rated at 20 amps and only dedicated for the kitchen. code states that there must be two 20 amp circuits supplying kitchen small appliances. bedroom outlets are fed by a 15 amp circuit most likely and that circuit is most likely feeding two rooms or so.
How does a circuit breaker trip and what causes it to do so?
A circuit breaker trips when there is an overload of electrical current flowing through it. This can happen when too many devices are plugged into the circuit or if there is a short circuit. When the current exceeds the breaker's capacity, it automatically shuts off to prevent overheating and potential fires.
