0
What else can I help you with?
Torsional rigidity of a solid circular shaft of diameter d is proportional to?
inversly proportioal to cube of diameter
Find the angle of twist per metre length of a hollow shaft of 100 mm external diameter and 60 mm internal diameter if the shear stress is not to exceed 35 MPa. Take modulus of rigidity G 85 GPa.?
Oh, honey, you want the angle of twist per meter of that shaft? Well, buckle up! First, calculate the shear stress using the formula τ = T*r/J, where T is the torque, r is the radius, and J is the polar moment of inertia. Then, use the formula φ = TL/GJ, where L is the length of the shaft, G is the modulus of rigidity, and J is the polar moment of inertia. Plug in those values and you'll have your angle of twist per meter. Easy peasy lemon squeezy!
How do you calculate Volume of circular shaft?
(Pi x R x R) x H... Where R is the radius of the shaft and H is the height.
What word goes with go hand mine rate to make a compound word?
Oh, dude, the word that goes with "mine" and "rate" to make a compound word is "shaft." So, when you put them all together, you get "mine-shaft" and "rate-shaft." Like, you're basically creating a whole new word by smashing them together.
Is higher number in Celsius colder than the lower number?
Shaft
What is the formula to calculate weight of solid shaft?
The formula to calculate the weight of a solid shaft is weight = volume × density × acceleration due to gravity. The volume of a solid shaft is calculated as π/4 × (diameter)^2 × length, where the density of the material and acceleration due to gravity are constants.
What is the weight of 1 meter SS SHAFT?
The weight of a 1 meter stainless steel shaft will depend on the specific grade and dimensions of the shaft. To calculate the weight, you would need to know the diameter and thickness of the shaft, as well as the density of the stainless steel material being used. You can use online calculators or reference materials to find the weight based on these factors.
How do you calculate weight if length width and thikness given of hollow shaft?
You cannot. The mass depends on the material of the shaft and that has not been specified.
Relationship between volume of cube and diagonal length?
3 meter shaft is connected to a motor to a generator calls for the use of the use of the shallow shaft with an inner diameter of 100mm and the outer diameter of 150mm.knowing that the allowable shearing stress is 85 Mpa . determine the maximum torque that can be transmitted a) by the shaft as designedb) by a solid shaft of the same weight the material density is7800kg/m^3 .
What are three standard dimensions of the needle?
-length-outside diameter of shaft-wall thickness
How do you calculate weight of shaft?
The weight of a shaft can be calculated using the formula: weight = density * volume * acceleration due to gravity. The density and volume of the shaft material will need to be known in order to plug them into the formula.
What a three things a vernier caliper measures in a garage?
1. A shaft diameter 2. Length of bolt 3. Inside of a hub
What is the formula for calculating weight using a mild steel cylinder?
gear with shaft dia40mm length 230 teeth 14 shaft dia 25mm width 6.5mm length 168mm
How do you calculate the weight of cast iron?
To calculate the weight of a piece of cast iron, you would need to know its volume and density. The formula to calculate weight is: weight = volume x density. You can find the density of cast iron online or in reference materials.
What is the swing-weight of the Cleveland 588 RTG wedges?
The swing weight will depend on the weight of shaft, length of shaft, lie angle and weight of grip. Your best bet to determine the SW is to bring it to a club builder/store and have it measured.
What is stronger solid shaft or hollow shaft?
Depends on what you mean by "better". For the same dimensions, a solid shaft will be a bit stronger, but also a lot heavier. If you were to make a hollow shaft of the same weight, but a bigger diameter, it'd be a lot stronger than the solid shaft.
How do you choose bevel gear diameter?
the inner diameter is the shaft diameter the out diameter you have to calculated
