0
How much should it cost to repair an sh capacitor 10000 AFC protected non pcb percent 5 plus percent mfc 440 vac 50 60 hz made by packard stock?
Wiki User
∙ 11y ago
10
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What is the opposite word for break?
repair
At a TV repair shop the amount charged for labor depends on the time the repair technician works. shows this idea expressed in function notation?
Amount(hours worked)
True or false the cells of organisms use energy for growth and repair?
false
What is the defention of seaworks?
Artificially enclosed basin into which vessels are brought for inspection and repair.
3 functions of cell division?
The three functions of cell division are reproduction, growth, and repair
How do you repair a 680 microfarad capacitor?
To repair a 680 microfarad capacitor, buy a new one and install it in place of the old one. It is unrealistic to attempt repair of a capacitor.
Dissasenble guide for Acer al1916w?
http://www.overclock.net/t/967253/monitor-repair-capacitor-replacement-tutorial
Does HP Solution Center offer repair services?
"The HP Solution Center is a software program run on Hewlett-Packard computers to diagnose software problems. It will repair some minor ones, but major ones should be left to a repairman."
What type of portland cement concrete should be used when the repair can be protected from traffic for 24 hours?
type 1
What is cost of repair of 240.00 plus 7 percent sales tax?
16.80
Will a bad capacitor cause your fan and compressor not to work?
Yes, but usually one side of the capacitor will completely go out. Either the fan or compressor will not work. First look at the capacitor. Usually they swell and the cylinder shape becomes rounded on the bottom or top. If you know how to work a meter, disconnect the leads on the capacitor and check for continuity (ohms). Put one lead on the Common and the other or Herm then move it to fan. Look for a rise and fall in ohms. If its bad, continuity will be lost on either side. Depends on what you are trying to repair, fan or compressor.
Where is lumber most used?
New housing accounts for 40 percent of all lumber use; remodeling and repair, 28 percent; nonresidential and manufacturing, 15 percent; and shipper containers, 9 percent.
Blower And Capacitor Parts?
The draft boost blower for the Fasco Motor is available as a furnace repair replacement part. It has single speed at 3000 RPM with sleeve bearing. This blower is for heaters, oil and gas furnaces. It operates on 115 volts with 0.7 amps. There are also different kinds of capacitors that can be replaced. The 10m - 370 volt, oval motor run capacitor or the 440 VAC, dual round capacitor can be used as replacements.
Why does a 1996 Chevy S-10 airbag light come on?
It is on because there is a problem with the SRS (Sublimental Restraint System). Do not attempt to repair. Serious injury can occur. Take this to a GM delaer for the repair. Your SRS may not be working at this time and you may not be protected.
Which company will do home appliance repairs for a reasonable cost?
http://www.searshomeservices.com/repair?psid=65162066&sid=HSRx20090527x00037. Check this website out They will give you ten percent off in home services repair
How do you determine the value of the feedback capacitor connected between the emitter and collector of the output transistor in an FM transmitter?
This is a vague question. Which transistor, and what is the make of the FM trasmitter? What do you really want to do, design an FM transmitter or repair an existing one?
How do I test a capacitor when I cannot remove it out of circuit?
You cannot. It must be taken out of the circuit and then tested on its own.That's not 100% true because, if it has wires at its ends, you can cut through one wire with an appropriate tool and then test the capacitor "out of circuit". If the capacitor is ok you can then re-join the two cut wire ends by applying a blob of solder carefully. (But, to avoid damaging the capacitor, use a suitable heat sink to shield the body of the capacitor from the heat of the soldering iron.)With direct current a capacitor also works like a special type of resistance. Whilst being charged up, it will show low resistance. As it slowly (or quickly) charges, the resistance will grow larger and larger. Whenever I repair circuitry and I have doubts about a capacitor (in the uF area) I simply use my multimeter on its Ohms setting. If a capacitor has shorted, then the result will be 0 Ohm. If the capacitor is working, or partially working, the resistance will gradually increase until it is out of range of the multimeter.Use an ohm-meter first to test the on-board capacitor and then use it to test a similar capacitor off-board, to see if the results sort of match up.Most often they will not match completely as on-board you also measure the effect of all other components connected into circuit with the capacitor. It might point you in the right direction though.On a separate thought, if you really cannot remove it, or disconnect one of its connections, then why test it at all? If it really can't be removed to replace it, then it makes no sense to test it!A capacitor can be tested using multimeter without removing it from circuit. but in order to check it, its polarities should be noted and then keep the positive terminal of multimeter on positive of capacitor and negative terminal on negative. It is vital to note that the readings will be affected by the remainder of the circuit. To test for capacitor function in circuit demands a good understanding of the circuit operation.Of course there are ways to test capacitors, both in circuit and out. While a truly accurate test involved taking the cap out of circuit, a basic test can certainly be done in circuit.Out of circuit, one can either connect to a VM, or better yet, an oscilloscope, and measure the time for voltage to decay to zero across the capacitor. This time should equal the time given by the equation for the time constant, and is dependant on the values associated with that particular capacitor.For RC circuits, this equation equals:τ = R × C. It is the time required to charge the capacitor, through the resistor, to 63.2 (≈ 63) percent of full charge; or to discharge it to 36.8 (≈ 37) percent of its initial voltage. These values are derived from 1 − e − 1 and e − 1 respectively.It is important to keep in mind that one must apply a voltage across the capacitor at its rated value. Thus, if it is a 400V capacitor driving a tube amp, for instance, it must be driven at around 400V. Driving it at 12V will lead to useless results.The only proper way to check for a capacitor value and or leakage is with a proper test bridge: set it to the capacitor's DC rating with it removed from the circuit completely. Any other way is just waste of time.Additionally, a common in-circuit test for a electrolytic capacitor is to measure its Equivalent Series Resistance (ESR) which can be done with an ESR meter. This is a quick and easy way to locate failing electrolytic capacitors, especially in power supply circuits.An effective method of testing any component in-circuit is with an in-circuit curve tracer. If you have an oscilloscope with X-Y input mode you can easily build one of these on your own. They do take some getting used to before you can use it effectively and are most useful for good board vs. bad boardcomparison.
