0
what is that .-.
Add your answer:
Earn +20 pts
When the Cartesian coordinate system is used to describe three-dimensional space one needs three axes. These axes are typically called the and axes.?
x, y and z axes.
Does every point lie on a quadrant why?
No, because point on the axes are not in any of the quadrants.No, because point on the axes are not in any of the quadrants.No, because point on the axes are not in any of the quadrants.No, because point on the axes are not in any of the quadrants.
What axes of symmetry does a rectangle have?
A rectangle has 2 axes of symmetry.
How many axes of symmetry does a rectangle have?
a rectangle has 2 axes of symmetry
How many axes of symmetry does regular pentagon has?
It has 5 axes of symmetry
How do you level a dumpy level?
it is a spirit level
What is the advantage of auto level than dumpy level?
The auto level makes it easier to do the work. Using the dumpy level requires you to put in all of the work.
How do you do temporary adjustment of dumpy level?
It as 3 following steps to adjust the dumpy level 1.SETTING 2.LEVELLING.3FOCUSING
What is advantages and disadvantages of dumpy level?
One advantage of the dumpy level is that it is extremely mobile. A disadvantage is the difficult in using and making accurate measurements.
What level do you use to shoot a datum?
Dumpy
Why is dumpy level known as dumpy level?
It is named so because of the shorter telescope it uses and also because in the original dumpy level the eye piece was an inverting lens such that it gave a shorter view for the same power of lens compared to wye level.
How do you use dumpy level to find the relative heights?
Dumpy level provides a horizontal line (parallel to earth's curvature); you can read the scale by holding it normal to the ground level. Take separate readings for separate points then compare them
How do you calibrate a dumpy level?
AIM/PURPOSE: To describe the instruction for the calibration of Dumpy Level to ensure that equipment is maintained in fully serviceable condition, is safe to operate and meets environmental requirements. FOR THE CALIBRATION OF DUMPY LEVEL The method described below is to be used on-site check prior to use as to the accuracy of the Dumpy level between calibration checks. This Work instruction shall be conducted at the commencement and completion of a contract. 1. Drive two pegs, "A" & "B", into the ground six metres or more apart 2. Set Dumpy up at "C" 3. Shoot a level at "A" and "B" 4. Relocate Dumpy to "D" and shoot a level at "A" and "B" 5. Record the appropriate result in the workbook. (Levels shot at "D" should be within ± 10mm of "C") D A C B
How do you adjust the the dumpy level?
First take the dumpy level to the place of surveying and place the tripod on the ground. Make sure that the three points of the tripod is placed such that the observer can take readings quite easily. Then take the dumpy level and place it on tripod and fix the center nut and make sure that the dumpy level doesn't shake. Then check the bubble level in the dumpy level and use adjust the main level screw so that at least 2/3 of the bubble is inside the circular area of the bubble level. Then adjust it by the other two screws and rotate the dumpy level 90 degrees and check whether the bubble shows a leveled stage. If it shows that the bubble is centered then it is O.K the dumpy level is leveled..... Then in order to take a reading, the u bubble should have to be leveled adjust the screw in the right side(there are a few adjusting screws,please get to know the actions performed by the screws, for that we must handle the instrument for sometime) and make sure the 'U' shape is formed. Now the instrument is ready take readings.....
What is a dumpy level?
A dumpy level (or spirit level) is used to establish the height difference between two measured points; or can be used to establish points (over an area/ or horizontal plane) which have the same height.Dumpy levels have been replaced by more modern laser leveling devices, but are still used extensively in the construction industry as they are cheap and easy to use (although not as accurate as laser levelers).Dumpy level
What is the Difference between dumpy and tilting level?
A dumpy level is a type of surveying instrument that has a fixed horizontal line of sight, whereas a tilting level can be manually adjusted to tilt in order to measure slopes or inclines. Dumpy levels are simpler to use and provide accurate horizontal measurements, while tilting levels are more versatile for measuring slopes and inclines.
What is the difference between a theodolite and a dumpy level?
A theodolite is a precision instrument used for measuring horizontal and vertical angles, typically for surveying and construction purposes. On the other hand, a dumpy level is a simpler instrument used primarily for determining height differences and leveling over short distances. Theodolites provide more accuracy and versatility in angle measurement compared to dumpy levels.
