0
Add your answer:
Earn +20 pts
What normal household objects are 2 2.5 and 3 millimeters in diameter?
The cores of electric wires and cables.The cores of electric wires and cables.The cores of electric wires and cables.The cores of electric wires and cables.
What are the materials used to make a calculator today?
Made of plastic, wires, buttons, a computer, and a screen
My Yamaha HTR 5935 Receiver powers off after a few seconds. Why?
I had this same problem. I had mixed up the wires on one of the speakers and the system was turning itself off to keep from overloading. Make sure your negative wires are going to the negative output on the system.
What do the horizontal lines on an ekg measure?
The horizontal axis is time. The vertical axis is a measure of something electrical (the wires are connected to electrical contacts on your chest).
The four wire three phase 220v delta system shown here includes a center tap of winding 1 a single phase 120v load may be safely connected between which two wires?
: This seems like a question from an electrical course, and is probably best answered by your course materials. : It's your test question, not ours, and there won't always be someone else to ask for the answer. Earn your diploma.
Why shouldn't you have trailing wires near a computer?
A large number of accidents around the work place, are cause by tripping over trailing wires this is all I have got sorry but i have a few ways that you can prevent it, this might help How to prevent accidents from trailing wires: •Tuck in all wires, so there not near where everybody walks •Use keyboards, mice that are wireless this would reduce the amount of wires that are around the workplace, so it would reduce the chance of someone getting injured of the wires being damaged. •Spread the computers out so that there not all cramped together, this would mean that there are not as many wires around the workplace, which would reduce the chance of someone being injured or the wires getting damaged.
These should not be allowed to trail across the floor?
Long trailing objects can be a safety hazard, causing tripping or snagging. Keep items like cords, cables, or textiles properly secured or elevated to prevent accidents and maintain a tidy space.
What safety precautions apply to trailing power leads?
For safety precautions trailing power leads should be individually capped off. This can be done using a plastic tape designed especially for electrical wires or a permanent plastic cap.
Tack Your Surround Sound Cables To The Baseboards For An Uncluttered Room?
When you set up your new surround sound system, make sure that you nail or staple the wires to the baseboard on the wall. You do not want to leave them trailing across the middle of the room. This looks very bad. It is also dangerous because people could trip on the wires and fall. If they are nailed to the wall, they will be unobtrusive and you will not have any problems with them.
Why is it important not trail wires across the floor?
shut your mouth
What wires are best used for heating floor tiles?
copper wiring would be best for heating floor tiles.
How does a pylon work?
A pylon holds up the wires carrying electricity. If there were no pylons the wires would drag onto the floor and if you were to tread on them you would get electrocuted by the wires.
What happens if you leave you wires hanging?
shape of planet's orbit
88 non turbo convert 13b wont start after changing coil wires What is the right placement?
Both the leading and trailing coils are marked for where they go into the block. The front of the motor is "1", and the second half is "2". The spark plug holes are marked for "L" Leading, and "T" for Trailing.
How do you remove engine from citroen Picasso?
take out bolts & wires lift it up & put it on floor
Will a knock sensor not let a car start if the sensor is bad?
it shouldnt. it could have stripped wires that report wrong info, causing timing to retard until no compression, but usually it will just put in generic figure until you replace it
What order do the spark plug wires go in on a 1988 RX7?
The big coil pack goes to the top, the front rotor is number one. they are usually labeled on the block with a L and a T. That stands for leading and trailing. Hope this helps.
