0
Depending on the condition of the piece, $550-$650, though prices vary by location. Generally speaking, prices are moving upward at the rate of approx. 10-15% a years, so expect to pay more in the future...
LoneStar
N-477741 was manufactured in 1978. A 3 1/2" barrel is one of the most sought after barrel lengths simple do to the look the weapon with that length barrel. Currently a unfired 27-2 with the 3 "T"s with the original box, paperwork and cleaning tools can bring $1000.00 to $1595.00. With no box and in 90% + condition should bring $750.00+. If the gun is nickle plated you can add 20%. Check and see if the grips are serial numbered to the gun. Most came with magna grips. To determine if the hammer and trigger are actually "target" you need to measure them. A .500 hammer is "target" .400 is "semi target." A "target trigger" will measure .400 and a "service trigger" will measure .265. Target grips, hammer and trigger (3 "T"s) would have been a special order.
What else can I help you with?
How do you tighten front wheel bearing on a PT Cruiser?
They are not adjustable, if loose they must be replaced.
What is the date of manufacture of a Browning 325 bearing the serial number 54313PP?
1988
What is the year of manufacture of a browning b-325 bearing serial number 51630NY?
1992
How do you manufacture taper roller bearing cage?
Type your answer here... Sheet metal taper roller bearing cages manufactured by (1) DRAWING (2) Window Cutting for rollers (3) Printing and (4) Bulging operation.
How can I properly support a load-bearing wall?
To properly support a load-bearing wall, you can install temporary supports, such as adjustable steel posts or beams, to carry the weight of the wall while you work on reinforcing it. Consult with a structural engineer or contractor to determine the best method for your specific situation.
How do you adjust ball bearings?
You can't, only tapered roller bearings as used in drums & rotors on some vehicles are adjustable. The rest are just sealed bearings and/or hub & bearing assemblies that are sealed
What kind of products does Yomega manufacture?
Yomega is an well known suppler of yo-yos. They innovated the transaxle system which does not use a ball bearing in the Yomega Brain one of several popular models.
How do you adj front wheel bearing?
That depends on the year, make, and model of vehicle. Please ask a new question with more info.Most newer vehicle have non adjustable sealed bearings.That depends on the year, make, and model of vehicle. Please ask a new question with more info.Most newer vehicle have non adjustable sealed bearings.
The clutch does not properly disengage causing gear grinding Renault master is the clutch adjustable?
there should either be a screw adjuster on the arm that pushes on the throw-out bearing or similar. I had many old Renaults and always did clutch adjusts on them without problems, don't remember exactly how. But if you aren't dissengaging then the throw-out bearing is not pushing in far enough, so you need to adjust so there is more pressure on the throw out bearing when it is not engaged, so when it is engaged (clutch pushed in) it pushes farther. Be careful or when not engaged you could have clutch-slip. To find the adjuster, find the arm coming out of the clutch housing, just follow it back and you will find the adjuster, has to be a screw pushing the lever, or maybe a screw on the back on slave cylinder that pushes the plunger in/out against the throw out bearing arm.The master cylinder is not adjustable, the adjustment will either be on the slave cylinder or someplace in that area.
Is it bearing or baring gifts?
It is "bearing gifts" (as in "carrying" them).
Why will transmission not go into reverse without grinding since replacing clutch?
The clutch is not adjusted correct, if adjustable, I don't know the year your working on. There is air in the system, needs to be bleed again real good. Could have wrong throwout bearing too.
What is bearing crush?
Interference between journal bearing to bearing housing is called bearing crush.
