0
To draw a rhombus using the Logo programming language, you can use the following commands:
- Use the "forward" command to move the turtle forward.
- Use the "right" or "left" command to change the direction of the turtle.
- Repeat the forward and turn commands to create the four sides of the rhombus, ensuring that the opposite sides are of equal length and the angles between adjacent sides are 90 degrees.
- Finally, use the "penup" and "pendown" commands to lift and lower the pen as needed to avoid drawing unnecessary lines.
What else can I help you with?
What is the logo command for rhombus?
In Logo programming, the command to draw a rhombus can be achieved using the combination of FORWARD and RIGHT (or LEFT) commands to create the desired angles. A typical command sequence might look like this: REPEAT 2 [FORWARD 100 RIGHT 60 FORWARD 100 RIGHT 120], where you adjust the angles and lengths as needed to create a rhombus shape.
What store has a logo that looks like a rhombus?
Renuealt
What store has a logo that looks like a silver rhombus?
Renuealt
How do you draw triangle using blackcat logo?
fd 50 rt120 fd50 rt120 fd50 rt 120
What commands to draw heptagon in logo?
To draw a heptagon in Logo, you can use the following commands: REPEAT 7 [FORWARD 100 RIGHT 51.43] This command moves the turtle forward by 100 units and turns it right by approximately 51.43 degrees, repeating this process seven times to form a heptagon. Adjust the FORWARD value to change the size of the heptagon.
What is the logo command for rhombus?
In Logo programming, the command to draw a rhombus can be achieved using the combination of FORWARD and RIGHT (or LEFT) commands to create the desired angles. A typical command sequence might look like this: REPEAT 2 [FORWARD 100 RIGHT 60 FORWARD 100 RIGHT 120], where you adjust the angles and lengths as needed to create a rhombus shape.
How do you draw nonagon using logo command?
repeat 3 [fd 250 rt 120]
How do you draw hexagon using repeat command of logo?
To draw a hexagon using the repeat command in Logo, you can use the following code: repeat 6 [forward 100 right 60] This command will move the turtle forward by 100 units and then turn it right by 60 degrees, repeating this process six times to create a hexagon. Adjust the forward distance to change the size of the hexagon.
What is SETH command used for in logo?
SETCH command is used to point the command its head in any direction without using the RT or LT.
How do you draw an octagon using Logo command?
An octagon is an eight-sided pentagon where all sides are equal length and all angles are equal. To draw an octagon in Logo, you move forward the length of a side and then turn 45 degrees, repeating 8 times (8x45=360). The following will therefore draw an octagon with a side length of 100 pixels: repeat 8 [fd 100 rt 45]
What store has a logo that looks like a rhombus?
Renuealt
How do you make a trapezium in MSW logo?
Well, honey, to make a trapezium in MSW Logo, you gotta use the "FD" (forward) and "RT" (right turn) commands to draw the sides of the trapezium at different lengths and angles. Just remember to keep track of your angles and side lengths to get that trapezium looking sharp. And if you mess up, just hit that "CLEARSCREEN" command and start over - ain't nobody got time for crooked trapeziums!
What store has a logo that looks like a silver rhombus?
Renuealt
How do you make circle in msw logo using repeat command?
repeat 360[fd1 lt 1]
How do you mke a square using repeat command FOR LOGO?
Repeat 4 [fd 60 rt 90]
Write logo commands to draw the rectangle figure?
write the logo commands to draw the triangle
How do you draw a cycle in MSW Logo?
To draw a cycle in MSW Logo, you can use the REPEAT command along with the FORWARD and RIGHT commands. For example, you can type REPEAT 36 [FORWARD 10 RIGHT 10] to create a circular shape. This command effectively moves the turtle forward while turning it slightly, creating a smooth cycle. Adjust the numbers to change the size and smoothness of the cycle.
