0
7 and 5/12 ftlbs
The conversion between ft lbs and 89 in lbs are given .On finding the relation we get as follows .
we know ,that 1 feet lbs =12 inch lbs .
so,89 inch lbs = 7.4167 feet lbs.
Wiki User
∙ 8y ago
Wiki User
∙ 14y ago89 inches = 7 feet 5 inches = 7-5/12 feet
89 inch-pounds = 7-5/12 foot-pounds
Add your answer:
Earn +20 pts
How much is 10 percent of 89 pounds?
10% of 89 pounds= 10% * 89= 0.1 * 89= 8.9 pounds or 8 pounds 14.4 ounces
What is 10 percent off 89 pounds?
80.1 pounds.
5 pounds - 9 ounces how many ounces?
16oz = 1lb so the answer is 89 ounces
How many prime numbers are in 89?
89 has two factors: 1 and 89. It is a prime number.
How many feet are there in 1.78 inches?
There are 12 inches in one foot. Therefore, 1.78 inches is equal to 1.78/12 = 0.1483 recurring (that is, 0.1483333..) or 89/600 feet.
How many pounds are in 89 oz?
89 ounces = 5.5625 pounds
How many pounds will you get for 100euros?
About 89 pounds
How many pounds is 89 tons?
178,000 pounds.
How do you re-torque an oil pan on an 89 suburban?
Tighten to 20 foot pounds. Do not overtighten.
What is the proper torque for a 2004 Ford F150 transmission pan with the reusable gasket?
The torque is 89 inch pounds or 7.41 foot pounds. You should never reuse a transmission gasket. If you are doing work on the transmission, replace the filter, it usually comes with a new gasket.
What is 89 pounds minus 15 percent?
89 pounds minus 15% = 85% of 89 pounds = 89*85/100 pounds = 75.65 pounds
What is the torque specification on a water pump for a 1998 buick skylark wth a 3.1 liter engine?
According to the chilton manual the 5 water pump bolts torque to 89 inch pounds. The four bolts that hold the water pump pulley torque to 18 foot pounds.
How much is 10 percent of 89 pounds?
10% of 89 pounds= 10% * 89= 0.1 * 89= 8.9 pounds or 8 pounds 14.4 ounces
3.8 intake torque specs ford windstar?
For a 2000 Ford Windstar the lower manifold bolts are tightened in two steps. First to 44 inch pounds and finally to 89 inch pounds. The spacer section above, and the top cover, both "plastic" are tightened in a single step to 89 inch pounds each. There is of course a sequence involved in all three cases, but that is a bit difficult to describe here.
What are the torque specs for a Pontiac 3.8 intake manifold?
I'm pretty sure this is that same 3800 motor that gm uses in my mom's 2001 buick Le Sabre. Her intake was the fiberglass resin plastic and the torque specs are 89 INCH pounds. Make sure you use the right tightening sequence too. 89 inch pounds is for the upper intake or Plenum. 136 inch pounds is the torque specs for the lower intake
What is the torque spec for 1997 3.8 buick lesabre intake manifold?
The lower intake manifold to cylinder head torque specification is 132 inch pounds. The upper plastic intake plenum to lower intake should be done in three steps 22 inch pounds, 44 inch pounds and thirdly 89 inch pounds. Be sure to follow the appropriate tightening sequence diagram.
How much is 89 pounds in euro?
89 pounds is 96 euro.
