How to Lay Tile Floor?

Answer 1

Laying your own tiles will save you a lot of money on instillation, and if you have time and a stead hand, it can actually be pretty easy. Follow this short guide to learn how to easily install your own tile floor.

Begin by gathering the following materials: Chalk%09Chalk Line, Mastic, Mastic Trowel, Plane, Cement, Sandpaper, Steel Square, Ordinary Scissors, Brush, Level, Scraper, Tape or Folding Rule, and Hand Cleaner.

Step One: Prepare the base floor. Remove any tack or old tile before starting. Clean the floor with safe chemical cleaning agent. Nail down any loose boards if the floor is hardwood, and plane down any high areas. If the floor is in poor condition, it may be necessary to layer the floor with some sturdy plywood or particle board. If this is the case, cut squares and rectangles that will have staggered joints when you nail them to the floor.

Step Two: Locate the center of the room. This is where you want to start your tiling. Do this by finding the center of each wall and drawing a straight chalk line to the opposite wall. The point where the lines intersect is where you start. Take care, because you need to find the exact center for the tiling to turn out well.

Step three: Check your work with loose tile. Without grout, lay down the tiles in each direction until they reach the wall. If they fit well, and your lines are straight, proceed to step four. If not, relocate the center of your room.

Step four: Create your tile design. If your tiles are solid, you can just lay the tiles down in a basic coverage pattern. If you are using different colors, lay them down how you want them to look when you’re done. This will prevent those ’oh, i shouldn’t have grouted that one quite yet’ situations.

Step five: Apply the cement/grout. Lay down a layer of grout across the entire area you will be tiling. Wait a few minutes for the grout to become tacky (there should be an estimated time on the can). Once you can push your thumb in the grout and it comes out clean, your grout is ready for tiling.

Step six: Apply the tiles. Spread the back of each tile with some grout and place them on the floor allowing a little less than a centimeter between tiles. plastic spacers can be purchased to help maintain the spacing. Allow the grout to dry and remove the spacers. Fill in the gaps with caulk and wait for the it to dry.

At this point, the tile floor is done! Allow enough time for the grout and caulk to dry before using your new floors.

Answer 2

Laying your own tiles will save you a lot of money on instillation, and if you have time and a stead hand, it can actually be pretty easy. Follow this short guide to learn how to easily install your own tile floor.

Begin by gathering the following materials: ChalkChalk Line, Mastic, Mastic Trowel, Plane, Cement, Sandpaper, Steel Square, Ordinary Scissors, Brush, Level, Scraper, Tape or Folding Rule, and Hand Cleaner.

Step One: Prepare the base floor. Remove any tack or old tile before starting. Clean the floor with safe chemical cleaning agent. Nail down any loose boards if the floor is hardwood, and plane down any high areas. If the floor is in poor condition, it may be necessary to layer the floor with some sturdy plywood or particle board. If this is the case, cut squares and rectangles that will have staggered joints when you nail them to the floor.

Step Two: Locate the center of the room. This is where you want to start your tiling. Do this by finding the center of each wall and drawing a straight chalk line to the opposite wall. The point where the lines intersect is where you start. Take care, because you need to find the exact center for the tiling to turn out well.

Step three: Check your work with loose tile. Without grout, lay down the tiles in each direction until they reach the wall. If they fit well, and your lines are straight, proceed to step four. If not, relocate the center of your room.

Step four: Create your tile design. If your tiles are solid, you can just lay the tiles down in a basic coverage pattern. If you are using different colors, lay them down how you want them to look when you’re done. This will prevent those ’oh, i shouldn’t have grouted that one quite yet’ situations.

Step five: Apply the cement/grout. Lay down a layer of grout across the entire area you will be tiling. Wait a few minutes for the grout to become tacky (there should be an estimated time on the can). Once you can push your thumb in the grout and it comes out clean, your grout is ready for tiling.

Step six: Apply the tiles. Spread the back of each tile with some grout and place them on the floor allowing a little less than a centimeter between tiles. plastic spacers can be purchased to help maintain the spacing. Allow the grout to dry and remove the spacers. Fill in the gaps with caulk and wait for the it to dry.

At this point, the tile floor is done! Allow enough time for the grout and caulk to dry before using your new floors.