0
in most circumstances the ampacity of a 10 awg wire is 30 amps but should not be loaded to more than 80% of its capacity as a rule of thumb. there are certain instances were these values can change but like i said under "normal" conditions 30amps
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What gage wire of service wire is needed to run two 200 amp services?
for residential use 2/0 copper or 4/0 aluminum, if your talking long distances then you need to up size for voltage drop
Is the wire running to a 20amp breaker different from a wire running to a15amp breaker?
Yes, a 20 amp breaker requires AWG # 12 copper wire. A 15 amp breaker requires AWG # 14 copper wire.
What amp capacity will 8 AWG wire allow?
A #8 copper conductor with an insulation factor of 75 or 90 degrees C are both rated at 45 amps.
What is amp rating for 10 gauge fuse link?
A 10 Gage wire will carry 30 amps. But if you are talking 10 Gage fusible link wire then that's different, a fusible link wire is a delayed fuse & will melt if over loaded. The general rule of thumb in the automotive trade is use a fusible link wire 2 Gage smaller then the load wire. If you are using a 10 Gage wire then you should protect the circuit with 14 Gage fusible link. I hope this helps!
50 amp breaker needs what wire size?
6 AWG wire
What is amperage limit of 12 gage solid copper wire?
20 Amp
What is the Current carrying capacity of 300sqmm copper wire?
in air it will be 665Amps.
Can you hook up amp and sub to 1997 park avenue?
Sure. You can hook this up to any vehicle. It is easy to do. Just make sure you have the proper gage wire for the amp as a small gage wire can heat up. Also with a smaller gage wire you will lose some power to the amp.
What gage wire is needed for a 35 amp ac?
Use 8 gauge wire.
What size breaker should be used with ceiling fans?
Use 15 amp breaker with 14 gage wire or 20 amp breaker with 12 gage wire. Either way will work just fine.
What gage wire of service wire is needed to run two 200 amp services?
for residential use 2/0 copper or 4/0 aluminum, if your talking long distances then you need to up size for voltage drop
What gauge wire do you need for a 12 amp?
For safety, approximately 6 or 8 mm. A #14 AWG copper wire with an insulation factor of 90 degree C will have a capacity of 15 amps.
Is the wire running to a 20amp breaker different from a wire running to a15amp breaker?
Yes, a 20 amp breaker requires AWG # 12 copper wire. A 15 amp breaker requires AWG # 14 copper wire.
Can you replace a 30 amp fuse with a 15 amp fuse?
Not a good idea. The 15 amp fuse will be protection a #14 wire which is rated for 15 amps maximum capacity. By changing the 15 amp fuse to a 30 amp fuse you would then be allowing 30 amps maximum capacity on a #14 wire. By doubling the load the extra heat generated on the smaller wire could be enough to melt the insulation from the wire and that could cause the wire to short out. If the wire shorts out inside the wall it means the removal of the wall board to replace the wire to restore the circuit to an operational condition. The proper wire sizing for a 30 amp fuse is, #10 copper wire with an insulation rating of 90 degrees C.
What size wire for 40 amp?
AWG # 8 copper.
What amp capacity will 8 AWG wire allow?
A #8 copper conductor with an insulation factor of 75 or 90 degrees C are both rated at 45 amps.
What size amp circuit breaker should be used for a gas dryer?
Typical residential electric dryers are on 30 amp circuits, which means 10 gage copper wire. The circuit breaker should match the dryer cord rating, generally 30 amps.
