0
It can be but usually results in a poor connection. It's best to use a sta-con connector where the wire is crimped with a crimping tool into the connector and then fastened under the screw.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
Can a wire be wrapped around a screw clockwise or counter clockwise?
Well, it CAN be wrapped either way, but because standard screws tighten when turned clockwise:if the wire is wrapped around the screw clockwise tightening the screw will pull the wire tighter around the screwif the wire is wrapped around the screw counterclockwise tightening the screw will push the wire away from the screw making it loose and maybe even popping the wire out from under the screwSo, if you want the wire to stay secure on the screw only wrap it clockwise!
Should solid copper or stranded copper be used with the pressure terminals of a duplex receptacle?
Either one can be used. Electricians prefer to use a solid wire and use the screw terminals rather that the pressure terminals. An eyelet can be formed with solid wire where as using stranded wire takes a bit more preparation to use. The stranded wire has to be wound tighter at the termination end. This is so that when the stranded wire is tightened under the screw terminal the wire does not splay into individual strands some of which do not get under the terminal screw. With some of the strands not tightened under the screw, this is the same as using a smaller size wire. The breaker feeding the receptacle is matched to a specific wire size. The now smaller wire size has a breaker greater than the ampacity of the wire. This could lead to overheating of the wire under full load and eventually cause a breakdown of the insulation. Once the insulation has broken down, the breaker will trip due to a short circuit. This wire will have to be replaced. This could involve opening the wall board to remove the burnt wiring should this happen.Most residential wiring is done with solid copper wire. In industrial applications, stranded THHN wire is used because many wires are run through conduits from service boxes and many different colors and gauges can be run to different locations. I personally would not use stranded in a residential application.
Can you put a receptacle on the end of an extension cord?
Yes, the receptacle will have to be terminated in a receptacle box of some kind. Construction usually use an FS type box with a 1/2" hub. A 1/2" strain relief connector is used to hold the extension cord into the FS box. Wire the white wire of the cord to the silver screw, black coloured wire to the brass screw and the green wire to the green ground screw on the receptacle. The cover plate should be weatherproof FS type if the cord is to be used outdoors. If for indoor use a normal steel cover plate designed for use on a FS box will work fine. If strictly for indoor use, a box called an 1110 utility box, will also work to hold the receptacle.
Can you use one length of 3-wire cable to provide electricity to 2 separate circuits?
In countries that use a single phase split secondary service you can. In modern homes this is the type of circuitry that is used for kitchen split receptacles. On the receptacle the tie bar is removed from the "hot" side of the receptacle. A red wire of the three wire cable is placed on the upper terminal of the receptacle. A black wire of the three wire cable is placed on the lower terminal of the receptacle. The white wire is placed on the opposite side of the receptacle under the silver coloured screw. This will give you a full 15 amps capacity on the top portion of the receptacle and a full 15 amp capacity on the bottom half of the receptacle.
What color wire is attached to the narrowest slot in a duplex receptacle?
I do not know what you mean by long slot. The bare ground copper wire connects to the green screw or the ground screw. The black wire attaches to the copper or gold colored screw and the white wire connects to the silver or chrome screw. Both the gold and silver screws are on the side of the outlet. The ground screw will be on one end of the outlet.
An inclined plane wrapped around a cylinder is called?
A screw or a bolt is an inclined plane wrapped around a cylinder.
What is wrapped around a screw?
The part of a screw that is wrapped around the central shaft of the screw is normally called a thread. It can be described technically as an inclined plane.
A screw is really an wrapped around a cylinder?
A screw is really an inclined plane wrapped around a cylinder.
An inclined plane wrapped around a cylindrical post is a?
An inclined plane wrapped around a cylindrical post is called a screw.
What is defention of a screw?
A screw is an inclined plane wrapped around a post.
What is an inclined plane wrapped around a bar?
A screw is an incline plane wrapped around a bar.
An inclined planed wrapped around a post?
An inclined plane wrapped around a cylinder post is a screw.
What is wrapped around a screws rod?
The part of a screw that is wrapped around the central shaft of the screw is normally called a thread. It can be described technically as an inclined plane.
An inclined plane wrapped around a cylinded is a?
Screw
What is an inclined plane wrapped around a rod?
Screw
Can a wire be wrapped around a screw clockwise or counter clockwise?
Well, it CAN be wrapped either way, but because standard screws tighten when turned clockwise:if the wire is wrapped around the screw clockwise tightening the screw will pull the wire tighter around the screwif the wire is wrapped around the screw counterclockwise tightening the screw will push the wire away from the screw making it loose and maybe even popping the wire out from under the screwSo, if you want the wire to stay secure on the screw only wrap it clockwise!
An inclined plane wrapped around a cylinder post?
An inclined plane wrapped around a cylinder post is a screw.
