0
Yes, the receptacle will have to be terminated in a receptacle box of some kind. Construction usually use an FS type box with a 1/2" hub. A 1/2" strain relief connector is used to hold the extension cord into the FS box. Wire the white wire of the cord to the silver screw, black coloured wire to the brass screw and the green wire to the green ground screw on the receptacle. The cover plate should be weatherproof FS type if the cord is to be used outdoors. If for indoor use a normal steel cover plate designed for use on a FS box will work fine. If strictly for indoor use, a box called an 1110 utility box, will also work to hold the receptacle.
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How far do you put a GFCI from water?
How far do u put a GFCI receptacle from water
Can you put two switches and GFI receptacle in same box?
Yes, that is fine.
Do you need a gfci outlet if you have a gfci breaker?
Not if the GFCI breaker is supplying the circuit you are wanting to put the GFCI receptacle into.
Can you add a receptacle to an end of run switch?
No, the neutral conductor will not be in that box. The white wire in the end of run will be the return "hot" leg back to the light fixture. When wired this white conductor should have had a black tape marker put on it to signify that it was not a neutral conductor. That same conductor should also have had a black marker placed on the end in the fixture's junction box.
How do you install 220 receptacle with white black and bare wires?
Assuming the wires are the correct gauge for application and breaker you use black and white wires as hot. Put red electrical tape on each end of white wire and connect red and black to the breaker output and bare wire to ground lug in panel. At receptacle connect black and red to hot contacts and bare wire to ground lug.
Can you use 6 gauge wire on A extension cord and put 30 amp plugs on it?
If your question is can you use a #6 flexible SOOW cord and put a 30 amp plug on it, then yes. The breaker that feeds the receptacle that the cord will plug into can be no larger than a 30 amp breaker. What limits the cord capacity to 30 amps is the ratings of the plug on the end of the cord.
How do you put a household receptacle on the end of an extension cord?
Yes, the receptacle will have to be terminated in a receptacle box of some kind. Construction usually use an FS type box with a 1/2" hub. A 1/2" strain relief connector is used to hold the extension cord into the FS box. Wire the white wire of the cord to the silver screw, black coloured wire to the brass screw and the green wire to the green ground screw on the receptacle. The cover plate should be weatherproof FS type if the cord is to be used outdoors. If for indoor use a normal steel cover plate designed for use on a FS box will work fine. If strictly for indoor use, a box called an 1110 utility box, will also work to hold the receptacle.
How do you put a longer cord on your dryer?
There are many ways in which you could put a longer cord on your dryer. You could put an extension cord on it.
What will cause a block heater cord to catch fire?
A break in the electrical wiring inside the cord - usually it is right by the male end that you are plugging in to power - so a replacement end can be put on the block heater cord ( those flames sure can startle a person ! ) After it happened to me , I always made sure that I plugged my block heater cord into my extension cord before I plugged my extension cord into the electric outlet
Can you plug in an iPod touch wall charger to an extension cord?
Yes, you can put the iPod Touch wall charger into an extension cord. That extension cord has to be plugged into a wall to be able to charge the iPod, though.
How do you construct a simple circuit?
STEPS IN CONSTRUCTING A SIMPLE ELECTRIC CIRCUIT:1.Prepare the materials.2.Remove the bulb from the receptacle.3.Unscrew the screw in the receptacle using a screw driver.4.Extend the cord of a wire using pliers.5.Connect the cords of the wire in between the loosen screw and the receptacle.6.Put the bulb again on the receptacle.7.Attach the cord at the end of both batteries.
How do you construct a simple electric circuit?
STEPS IN CONSTRUCTING A SIMPLE ELECTRIC CIRCUIT:1.Prepare the materials.2.Remove the bulb from the receptacle.3.Unscrew the screw in the receptacle using a screw driver.4.Extend the cord of a wire using pliers.5.Connect the cords of the wire in between the loosen screw and the receptacle.6.Put the bulb again on the receptacle.7.Attach the cord at the end of both batteries.
What kind of sentence can you put extension in?
Extension: A part added to something to enlarge or prolong it; a continuation The action or process of becoming or making something larger. The barn is in the process of having an extension for the horses added to the side. The power cord was not long enough to reach the playhouse so father got an extension cord for me.
What is the use of extension?
you can put it to the end of the filename: somesource.c
Can you put an extension cord on a treadmill 20 amp?
Make sure the wire size of extension cord is AWG 12 or AWG 10. Also circuit must support the 20A at main panel. Standard household extension cords are usually AWG 14 which are not sufficient to carry 20A.
What is the use of extension C?
you can put it to the end of the filename: somesource.c
How do you plug a i pod touch cord into your laptop?
Put the USB end into the USB slot then connect your iPod to the other end. :-)
