0
That's no problem.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Can you use a range 220 for a dryer 220?
The plugs are different. The prongs are straight on one and angled on the other. The wire and breaker are the same. You can either change the outlet or the cord.
Can multiple circuits be connected on one breaker?
Multiple wires can be connected to one breaker but the one breaker IS a circuit. As long as the load is not more than 80% of the breaker capacity (example: a 20 amp breaker can only have 16 amps or 1920 watts at 120 volts) then by code as long as the load is not a specialty outlet of some sort, you can have as many outlets you want.
Can you wire 2 bedroom on 1 breaker?
You can't wire 2 beedrooms on one breaker.
What are examples of inclined planes in the Bathroom?
The shower is one example.
There's two in every room one on every corner?
Bathroom
What is the solution for a refrigerator that is tripping the GFI?
When wiring a house, GFI plugs are strategically placed in areas that can be tripped by water. For example: in bathrooms, in garages, etc. There are certain areas that do not require GFI plugs. A refrigerator is one device that is usually on its own breaker and does not require a GFI plug. My recommendation is to locate where the refrigerator is. If it is in the house remove it and replace it with a non GFI plug.
Can a hair dryer trip a gfi receptacle?
Yes, it can.Our bathroom GFI trips, when my wife uses one particular hair drier.
Where do you install GFI devices?
The areas that should be protected - Exterior plugs, garage plugs, plugs next to a sink or tub. Kitchen and / or island plugs. Remember, one plug can protect an entire circut.
Does garbage disposals have a breaker?
Yes but the breaker would be at your electrical panel, they do not have a breaker connected to the garbage disposal but they do have a reset button on the bottom of the garbage disposal. Most modern homes also have a GFI outlet linked to the garbage disposal. If your disposal is tripping breakers or GFI outlets I would consider that something is very wrong with your disposal, or you installed one with to much power!
How do you find a triped circuit?
Check the circuit panel / breaker box. The tripped breaker should be partway between 'OFF' and 'ON'. If nothing else, turn the breakers off then on, one at a time and when the tripped breaker is reset, the circuit should be live again. Also check GFI outlets. If one is in fault condition, it will need to be reset. If the tripped GFI outlet is protecting other outlets, they will come back when the tripped GFI is reset. These sockets seem to hide in many cases... Behind microwave ovens for example or refrigerators.
If power is out in one room of the house but the breaker was not tripped what could be the problem?
Check the connections to all the receptacles. On a spur, it's possible that one wire slipped off and then that breaks the circuit, not likely on a ring circuit. It is also possible that you have a GFCI (ELCB UK) in the run that might be tripped and that could bring the run down as well. Of course, the breaker might have tripped and the toggle not flipped over; try manually tripping and resetting it.
How do you find out why a GFI won't reset if it tripped several times due to Christmas lights and rain but they are now unplugged and when the reset button is pushed it immediately trips?
If the outlet cover was held open by the lights it could be wet. A smal amount of water will cause a GFI to trip. A GFI is a device which makes certain that voltage is not draining away from the two wires, to some OTHER voltage drain, such as a human body or a wet circuit. if above not the answer go to your breaker box and find the breaker that controls that circuit. you will know when you have the right one when the breaker does nothing, not even trip it self. see what else is on that circuit {what else turns off when main breaker is tripped and unplug everything that is on that circuit then turn on the main breaker. try the reset with everything else off if it still trips then its the gfi itself. they go bad often on construction sites [my own personal experience] if it resets properly than one of the other things on that circuit is the culprit. replug or turn them on one at a time. the breaker will trip if its one of these. if not replace the breaker. pretty cheap at lowes or home depot. turn off main breaker when you replace it. lots of luck!!
What can you do if you're newly installed dryer keeps tripping the electrical panel repeatadly and it also trips the GFI in the Garage at the same time?
If the GFI that is tripping is a different circuit, there is electrical leakage between the circuit the GFI is controlling, and the dryer circuit. It is possible that there is some cross wiring in the electrical box. I would strongly recommend getting a licensed electrician to look at it, preferably before you have a fire. If the GFI is the same circuit as the one where the dryer is plugged in, you might want to have the dryer checked for leakage to ground. You should also check the dryer circuit's rating against the rating of the breaker in its circuit. A dryer typically takes 30A on usually a single two-gang breaker; if you have a larger dryer that pulls, say, 45A, a 30A breaker will always pop. It sounds to me like a bad electrician has, instead of buying a proper two-gang 30-A breaker, installed your dryer across two circuits, one being the garage GFI circuit; the dryer, because it pulls 220V, pulls an unbalanced load across the GFI and triggers it, and the other circuit breaker is triggered because it loses the extra power provided through the GFI. I cannot emphasize this enough: get this checked out and fixed. Now. Before you get a house fire.
How do you connect the wires when replacing a socket that has a gfi button with one that does not have the gfi button?
Don't ! get another GFI plug. there 4 dollars and the instructions come with it
Why would the two light fixtures and one overhead fan in your bathroom all go dead at once and remain dead even though the breaker has not tripped?
Proably due to a GFCI breaker located in an outlet either in the bathroom or on the same circuit, possibly in another room like the kitchen or other bathroom. You will see the button on the outlet....
How do you replace a GFCI outlet?
The GFI outlet was there for a reason, such as a bathroom or other location around water where there is more risk of a shock being harmful or lethal. If it was a GFI, keep it a GFI. Also that outlet may be protecting other standard outlets being fed from the GFI. You can only after the house has passed inspection after the house was finished being built. It's a requirement that all new houses have to have a GFI wherever there's water, but it's perfectly legal once you buy the house to do this modification. However, it's highly not recommended unless there's more than one GFI outlet hooked up to the same circuit. If there's more than one, it's optional to take one off and replace it with a standard outlet because you really only need 1 GFI outlet to protect the rest of the outlets on the same circuit. But if it's already there, just leave it as is. Example: power box>GFI>normal>normal>GFI>normal; end; You can take off the second GFI and and every normal non-GFI outlet will function like GFI. If you take off the left one, only the last normal outlet will be GFI protected, the ons to the left wouldn't.
Which terminal on a 15 amp household breaker does the hot wire feed into and which one does it come out?
On a 15 amp household breaker there is no terminal on the in feed of the breaker. The breaker either plugs into the distribution panel's bus bar or it bolts to the distribution's bus bars. The feed conductor connects to the load side of the breaker at its terminal lug.
