0
Can you power a light switch power to switch then to light from a switch beside the one you want hot the switch that you want to take power from has the white as hot switch after light?
Wiki User
∙ 11y ago
I can not understand your question.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Have 3 lights Power to light 1 Need to connect light 2 then light 3 then down to single pole switch How do you wire?
You would wire the switch to the first light. Code says to break the black or power side of the circuit. Connect the white to the light. Take the black down to the switch on the black wire and back to the light on the white. This is a line of wire from the light to the switch. From the first light, take the white and the return white from the switch to the second with another run of wire. This will be regular black white with ground. White to white and at the first light the return line from the switch is white but hook to the black to the second light. Second light to third just continues the two wires. Black to black, white to white. I think this is clear enough to follow. If not, ask again.
How do you use a 14-3 wire for Switch and Power?
you need 2 , 3 way switches on the switch you will have 3 poles 1 will be copper 2 will be silver your 1 copper is power or switch your 2 silver are travelers to toggle the power back and forth , you use the black and red wires for the travelers and use the white for the power on one switch and the white to the other to the light with your neutral ---- power---* *--------* *---switch powered *--------*
What if your light switch has four wires two white and two black. Which one would be the hot wire and would two be the grounds?
One set, one white and one black are the power and ground coming in. The other set goes to the light. Probably, the one in the bottom of the switch box is the power in. In this case, it really doesn't matter. If you break the black wires, the light should work. Tie the two white together and connect 1 black to each terminal on the switch. White or ground goes to the light, black will feed through the switch either way and complete the circuit.
What is the white cable when connecting to a light switch?
On a light switch the white wire is neutral. All the neutral white wires are tied together under a wire nut and pushed back inside the box. The white is not connected to the switch.
How do you wire a light and switch with the 2 wire old romex?
with a standard 1 pole light switch (one switch operating the light) it is black wire to black wire and white to white (non grounded)
How do you wire a basic off switch to a light?
Light switch connection is usually straight forward. Find your incoming hot wires, black and white. With the switch in the off (down) position and the power disconnected , connect the black wire to the top screw of the switch. Find the load wires and connect the black to the bottom screw of the switch. Connect the two remaining white wires together with a wire nut and push them to the back of the switch box. Install the switch into the wall box, replace switch plate cover. Turn the breaker (power) back on. Flip the switch to the up position and the light should come on.
Why would a light switch have two black wires for power and two whites caped off?
Black represents Hot and White common. For the light to operate it needs a white and black wires. The switch box has two cables with a white and black wire plus a ground. One wire is from the supply and the other to the light. Connecting the whites just provides common directly to the light. The blacks go into and out of switch because it is the hot side that is being switched.
Im adding a new ceiling fan in my living room i pulled the old fixture down i noticed 2 sets of 3 wire BWR and 1 set 2 wire BW BW going to the wall switch how should you wire in the fan?
White is for neutral on the fan, black is power for the motor, and red is power for the light. If the power from the switch only has two wires (black and white), you would hook up white to white and hook black and red from the fan to the black wire from the wall switch. This means that you'll be powering the fan and light on the same switch and to change the fan and light separately you will have to pull on the chains or use a remote control.
New ceiling fixture goes on as soon as power is back even though switch is off?
You switched the power and switch wires. There should be two sets of wires in the ceiling box. 2 black, 2 white, 2 bare. Two groups of three. The white wire going to the light is the incoming wire. The black one in that group is the power coming in. Take that black wire and connect it to the other black wire. The second black wire goes to the switch. The power comes back to the light on the white wire of that set. Connect that white wire to the black wire in the fixture. The switch should work now. That is if everyone wired the house the way it is supposed to be.
How do you wire an additional light to another light with a switch?
In the wall switch box you should have a white and black pair from your source of power (120 volts). The other pair of black and white wires from the wall box should be going to the light fixture junction box. With the power off, connect the two white wires together with a wire nut. Connect the two bare copper ground wires together making sure that at least one of the ground wires goes under the green screw in the switch junction box. Turn the switch to the off position, no little indicator bump showing on the switch toggle lever. Now take the black incoming hot wire and put it under the top screw on the switch. Hot wires always go to the top of switches. Now put the black wire that is going to the light fixture under the bottom screw. Tighten both. Install the switch into the wall box with the switch handle in the down position. All switches when installed must be off in the down position. Install the switch plate cover.
How do you install a dimmer to a light installed with W wire B wire and ground W running into the switch box if the switch box has power from B wire W wire and ground?
If you have one wire into your switch box for your light. this is called a switch leg, the dimmer should be wired across the black and white wire wires.
Can you change an electrical outlet into a switch for a light?
Sure. For a light you need a fixture to hold the light and the light itself. The light needs to be connected to a voltage supply which you can get from the outlet. In the outlet box you will have a black, white and bare ground wire. Essentially you connect the white and bare wires directly to the light and switch the black wire (hot) through a switch.
