0
What else can I help you with?
How do you extend romex wire you moved an outlet you need to extend and connect?
You need to splice the extension Romex, using wire nuts, inside a covered junction box made for the purpose. If you can do it within the original outlet box you can put a blank cover on the box. If not you may have to install a new "old work" box in wall. If you can get to wire in attic or basement you could put the junction box in one of those locations. The junction box must be accessible so you can't bury it in the wall.
How do you convert a standard light fixture into a pull-chain one?
Shut off the power to the light circuit. Remove the old light switch if there is one. Remove the old lamp holder base. Make a diagram and note how the wires were attached, what colour screws to what colour wire. At the light switch wire nut the two wires that came off of the switch together. The switch plate cover will have to be replaced with a blank cover plate to cover the old switch box. Install the new pull chain lamp holder using the notes and diagram that you made. Some of the lamp holders that have a switch in them will not have terminal screws. The wire to the switch will be the "hot" wire. The other wire from the old lamp holder will be the neutral which should be a white wire. Insert the bulb and turn the power back on. Now the pull chain will control the light rather that the wall switch.
How do you repair a pull chain switch on a fluorescent light?
To repair a pull chain switch on a fluorescent light, you will typically need to replace the switch with a new one. Start by turning off the power to the light fixture, then remove the old switch by disconnecting the wires and unscrewing it. Install the new switch by connecting the wires as per the manufacturer's instructions and screw it back into place. Test the new switch to ensure it is functioning properly before turning the power back on.
How do you wire a tri-light bulb table lamp with 3 wire rotary switch?
If the tri-light needs a new lamp holder try any reputable lighting house store. These types of retailers have all of the parts that you need to repair any lamp configurations. The new switch will have a rotary switch built into it just like the lamp had when it was new. There are only two wires to connect to it. Don't disconnect the old one until you have the new one and just put the wires on the same terminals as the they are wires on the old switch.
Can you add 14-2 romex wire to old house wiring?
Yes, if the existing wiring you are adding to is 14 gauge. If it is 12 guage then you must use 12 gauge. If you are running wire from the service panel it is fine as long as you install a 15 amp breaker.
How do I properly wire a light switch in my home?
To properly wire a light switch in your home, first turn off the power to the circuit at the breaker box. Remove the old switch and connect the black wire to the brass screw, the white wire to the silver screw, and the ground wire to the green screw on the new switch. Secure the switch in place and turn the power back on to test the light.
How can I install a 2 wire light switch in my home?
To install a 2 wire light switch in your home, first turn off the power to the circuit at the breaker box. Remove the old switch and disconnect the wires. Connect the black wire to the brass screw and the white wire to the silver screw on the new switch. Secure the switch in place and turn the power back on to test the switch.
How do you wire up a light switch?
To wire up a light switch, you need to turn off the power, remove the old switch, connect the wires to the new switch (usually black to black, white to white, and ground to ground), and then secure the switch in place. Finally, turn the power back on to test the switch.
How do you properly wire a single light switch?
To properly wire a single light switch, you need to turn off the power, remove the old switch, connect the wires to the new switch (usually black to black, white to white, and ground to ground), and then secure the switch in place before turning the power back on.
How do you properly wire a dimmer light switch?
To properly wire a dimmer light switch, first turn off the power to the circuit. Remove the old switch and connect the dimmer switch's wires to the corresponding wires in the electrical box. Typically, you'll connect the black wire to the hot wire, the green wire to the ground wire, and the red or white wire to the neutral wire. Secure the connections with wire nuts and then carefully tuck the wires back into the box before attaching the dimmer switch to the box. Finally, turn the power back on and test the dimmer switch to ensure it is working correctly.
How do you wire a light switch in a home electrical system?
To wire a light switch in a home electrical system, you need to turn off the power, remove the old switch, connect the wires to the new switch (usually black to black, white to white, and ground to ground), and then secure the switch in place before turning the power back on.
How do you hook up a light switch properly?
To hook up a light switch properly, first turn off the power to the circuit at the breaker box. Remove the old switch and disconnect the wires. Connect the black wire to the brass screw, the white wire to the silver screw, and the ground wire to the green screw on the new switch. Secure the switch in place and turn the power back on to test the connection.
How do I properly wire an Eaton light switch in my home?
To properly wire an Eaton light switch in your home, first turn off the power to the circuit at the breaker box. Remove the old switch and connect the wires to the corresponding terminals on the Eaton switch - typically, the black wire goes to the "hot" terminal, the white wire to the neutral terminal, and the green or bare wire to the ground terminal. Secure the switch in place and turn the power back on to test the switch. If you are unsure, consult a professional electrician for assistance.
How do I install a 3-way light switch?
To install a 3-way light switch, first turn off the power to the circuit at the breaker box. Remove the old switch and identify the common wire. Connect the common wire to the dark-colored screw on the new switch. Connect the other two wires to the light-colored screws. Secure the switch in the electrical box and turn the power back on to test the switch.
How do you install a 3-way light switch?
To install a 3-way light switch, first turn off the power to the circuit at the breaker box. Remove the old switch and identify the common wire. Connect the common wire to the dark-colored screw on the new switch. Connect the other two wires to the light-colored screws. Secure the switch in the electrical box and turn the power back on to test the switch.
How do you hook up one light to one switch in a basement lighting system that has all 10 lights connected to one switch?
If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.
How do you extend romex wire you moved an outlet you need to extend and connect?
You need to splice the extension Romex, using wire nuts, inside a covered junction box made for the purpose. If you can do it within the original outlet box you can put a blank cover on the box. If not you may have to install a new "old work" box in wall. If you can get to wire in attic or basement you could put the junction box in one of those locations. The junction box must be accessible so you can't bury it in the wall.
