0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How many times does 120 go into 390?
Three full times. 120*3=360 390/120=3.25
How much is 39cm put into mm?
390. There are 10 mm in 1 cm, so 39 x 10 = 390.
Does a 440 or a 426 torque converter have the same weights as a 360?
nope. the 440 with six pack rods and a forged crank used a different amount of balance than a 440 with a cast crank. the 440 with a forged crank and normal rods was internally balanced and the 360 had a different balance as well.
How many minutes are there in 6 and a half hours?
There are 60 minutes to one hour, so 6x60=360. Half an hour is 30 minutes, so 360+30=390
How many minutes in 6.5 hours?
390 minutes. One hour is the same as 60 minutes. 6 hours is 360 minutes. Half of an hour would be 30 minutes, which brings the total to 390 minutes.
What is 360 increased by 30?
It is: 360+30 = 390
How toIdentify ford 360 and ford 390?
These engines are completely identical except for the crank and rods. The pistons are even the same. You can convert a 360 to a 390 by just replacing the crank and rods with 390 parts. The 360 was not a good engine. If you have a 360 convert it. The only way I know to tell them apart is to test the TDC. 360's come with the piston WAY down in the bore at TDC. They have zero quench, and zero compression. The pistons are close to 1/8" down in the hole at TDC! Converting to a 390 adds more stroke, brings the pistons right up to the deck at TDC, and provides for a nice compression increase over the dismal 8 to 1 of the 360. So if at TDC you have a 1/8 clearance, you have a 360. Of course you will have to remove a head to check this. Another thing is that if the engine came out of a truck it is more than likely a 360. If it has a 2 barrel carb it is more than likely a 360.
Can you bore a 318 engine to 340 cuin?
no you cannot bore it to 340 but you can put a stroker crank in it and get to 390, 396 and even more
What is the deal with the 360-30 line?
390
How do you put a 390 to a NP435 on a 1971 Ford F-250 4wd?
if it came with a 360 it will bolt right up the fe series of ford big blocks 360 390 401 406 427 428 429 460 and other small blocks use different bellhousings
How do you make a 360 cid ford into a 390 cid?
== == == == == ==
How do you make a 1969 ford 360 faster?
ford 390 heads, cam and 428 crankshaft. 360 and 390 shared the same block. you woul dthen have a 410 stroker
How many times does 120 go into 390?
Three full times. 120*3=360 390/120=3.25
What of these 128 225 360 and 390 is a square number?
225 is 15².
Is the Triumph 865cc parallel twin 180 or 360 degree crank?
It's a 360 or a 270 degree crank depending on which model of the twins you look at.
How do you find motor size on 1972 ford f-600?
It can have either a 360 or 390 V8. Most likely a 360.
What is the angle that measures 380 deegree and higher?
There is no special name. An angle of 390 degrees, for example, is effectively the same as 390-360 = 30 degrees.
