0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
How to run a cable underfloor from a wall socket?
Yes, as long as you do not run it under the floor joists. New electrical code requires that you drill a hole through the floor joists and run the wire through those holes. It cannot be hanging under the floor joists. If you see wires are already running under the floor joists then go ahead and run the wire under the joists attaching it on every other joists with a wire staple. Make sure they wire does not make contact with any metal ductwork or any other metal objects. Match the wire with what is already in the wall outlet you are jumping off of. If it is 12/2 then use 12/2, if it is 14/2 then use 14/2. Never mix wire gauges.
Can you run thhn conductors exposed?
n you run thhn wire in a cable tray
Will 2.5mm wire conduct 240 volts?
You size wire by the current. Various insulations are rated for voltage, temperature and the medium where the wire will be run.
Does 6 gauge wire need to be in a conduit if run in a finished garage along the wall and ceiling?
If you are talking about #6 building wire, it needs to have mechanical protection. This means that it has to be run in conduit. If you are talking about #6 cable set like Romex, then it only has to have mechanically protection below a five foot elevation from the garage's finished floor. If the wall that the cable set is running in is going to be finished with drywall or plywood then that is considered protected.
Should solid copper or stranded copper be used with the pressure terminals of a duplex receptacle?
Either one can be used. Electricians prefer to use a solid wire and use the screw terminals rather that the pressure terminals. An eyelet can be formed with solid wire where as using stranded wire takes a bit more preparation to use. The stranded wire has to be wound tighter at the termination end. This is so that when the stranded wire is tightened under the screw terminal the wire does not splay into individual strands some of which do not get under the terminal screw. With some of the strands not tightened under the screw, this is the same as using a smaller size wire. The breaker feeding the receptacle is matched to a specific wire size. The now smaller wire size has a breaker greater than the ampacity of the wire. This could lead to overheating of the wire under full load and eventually cause a breakdown of the insulation. Once the insulation has broken down, the breaker will trip due to a short circuit. This wire will have to be replaced. This could involve opening the wall board to remove the burnt wiring should this happen.Most residential wiring is done with solid copper wire. In industrial applications, stranded THHN wire is used because many wires are run through conduits from service boxes and many different colors and gauges can be run to different locations. I personally would not use stranded in a residential application.
How to run a cable underfloor from a wall socket?
Yes, as long as you do not run it under the floor joists. New electrical code requires that you drill a hole through the floor joists and run the wire through those holes. It cannot be hanging under the floor joists. If you see wires are already running under the floor joists then go ahead and run the wire under the joists attaching it on every other joists with a wire staple. Make sure they wire does not make contact with any metal ductwork or any other metal objects. Match the wire with what is already in the wall outlet you are jumping off of. If it is 12/2 then use 12/2, if it is 14/2 then use 14/2. Never mix wire gauges.
Is that possible to run romex wire to the under ground basement?
If the wire is to be buried you'll need to use "direct burial" wire; if you're staying inside the house, just under the floor and above the concrete or dirt, standard romex should be fine.
What is the best place to run power cord for subs on a 99 Pontiac TA?
i always run my power cords on the same side as the bat. drill through the firewall (carefully) run the wire above other wires to hold it up. then take off the plastic trim at the floor of the door and run the wire under that. take out the back seat, any extra wire can sit under the seat. run your remote wire from your deck to the amp on the same side as your power wire. run the RCA's on the opposite side as the power wire or you'll risk interference noise.
Where is the hole in the firewall on a 2003 impala to run a power wire from the battery to the amplifier?
You need to pass it under the car just under the passenger floor mat you have a hole just the right size for the cable
How do you wire the electric brake controller on a 2006 Liberty CRD with the factory towing option?
The brake wire is under the floor mat.
How efficient Is under floor heating?
Thermoset under floor heating installed is energy efficient and affordable. The materials run in the $260.00 range and installation depends on the size of the floor.
Where can you run a 4 AWG power wire through the firewall in a 2007 RAV4 for an amplifier setup?
Run the wire under the car and come up under a seat (front or rear) or where it's convenient.
How do you replace the dimmer switch in the steering column with one on the floor?
1. Got to the Public Library and request the Electrical Shop Manual for your year, unless you are able to locate the HI-BEAM wire. 2. Locate the wire that runs from the steering column switch to the C200 connector -- the very large connector the connects the steering column wiring harness to the firewall harness. 3. Either cut this wire and run the FIREWALL end to the new floor switch OR tie into this wire. NOT cutting it allows both column AND floor control. 4. Run the YELLOW wire from the HEAD/PARK Light Switch to the new floor mounted switch -- it's usually from pin 'D'.
How do you run a power wire on a 2005 Pontiac sunfire for subs through the fire wall with out drilling is there any plugs in the fire wall or do you have to drill?
YOu can easily run your wire from your battery, to just underneith your brake booster on your fire wall. There is a Bundle of wires going through the grommet in the firewall, going into the driverside wall. Then you pull up your floor trim on the driver side, and lay the wire where ever it will fit. Run it to the back of the rear seat, if you have one, and there you go. there is a rubber grommet under the brake booster. to access a wire to go through insert needle nose pliers through catch the wire ,hold, and pull
What if the floor at the back get really damp it still comes a day after running the AC Now there's a strong odor smells like acetone Does anybody have any idea Lexus ES300?
I can't tell for sure but the ac has a drain that goes through the floor under the dash on the passenger side. this can become clogged and cause the water that is created by the air conditioner to run under the carpet and into the rear floor which is the lowest point. the smell can be caused by meldew. There is a drain tube that is visable under the car hat you can run a small wire up into and clean it out but be careful and don't poke too hard as to damage the coil.
How do you hook up subwoofers in a 97 Chrysler cirrus?
first you have to run a wire from the red + terminal under the hood or in the left tire well where the battery is for a more direct connection then run rca wires from your head unit as well as a remote wire to your amp run those and the power wire to the amp and your all set
How do you remove the magnetism from a permanent magnet?
There are several choices:Drop it on the floor a few times.Heat it red-hot in a fire.Whack it with a hammer a few times.Wrap several turns of wire around it and run a high AC current through the wire.
