0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What does 40 time 350 equal?
It is so very simple and quick to get the answer, especially since, if you need it, you can use the calculator that comes with your computer. But since you are obviously not able to do so, the answer is 14000.
How many tons of sand do you need to cover 14000 sq ft 2 inches deep?
Approximately 117.5 tons of dry sand. I willl use 1602 kg/m3 as the density of the sand. (See http://www.simetric.co.uk/si_materials.htm) We need common units, so first I will convert 1602 kg/m3 to lbs/cubic yard. 1602 kg/m3 = 1602 kg/m3 * (2.2 lb/kg) * (1m3/1.093 cu yds) = (1602*2.2)/1.093 = 2721 lbs/cu yard Now figure out the volume of sand you need (in cubic yards). volume = (14000 sq ft)*(2 in) = ((14000/9) sq yds)*((2/36) yds) = (14000/9)*(2/36) yds = 86.4 cu yds weight = density*volume=2721*86.4 lbs = 235094 lbs = 235094/2000 tons = 117.5 tons
How much does 53 linear ft of carpet cost at 53 cents square foot?
The answer depends on how wide the carpet bolt is. For example, 53 linear feet of a 6 foot bolt is 318 ft2. At $0.53 per ft2, the cost would be $168.54. When the price is given in $/ft2, you need to know the width of the bolt to convert your linear foot needs into a price.
fuvk all of all?
all you need to do is calm down
Why do you need to tap the can 3 times on the first agitation?
it brings the carbonation down
How do you remove drive belt from Toyota Echo?
It's pretty easy. Locate the generator/alternator which is the top from pulley that the drive belt touches. On the bottom of the generator is a 12mm bolt, loosen this (but there is no need to take out off, just loosen it). There is a slider bracket on top of the generator with another bolt, loosen that one as well. I strongly recommend spraying penetrating oil (I like deep creep but there are many that will work fine) on the bolts and all along the slider area. Now that its loose you can push the generator back, taking the tension off the drive belt, now you can easily remove the belt. When you are ready to re-install, just pry the generator forward again until the belt is tight, you can use a pry bar, you really need two people for this, one to pull it back, and the other to tighten the slider bracket bolt down while the belt is tight. If you are putting on a new belt, you may want to check and re-tighten it after a break in period (couple days of driving). Don't forget to re-tighten the lower bolt on the generator after you have locked down the top bolt.
How can you break down your model 100 if you can't get the bolt to open?
You will need the services of a good gunsmith
How much would a Yamaha generator cost?
Prices vary for a Yamaha Generator depending on the size of the generator. The more wattage involved, the more you will need to pay. First you need to determine the size of generator you need then contact a local retailer.
What amperage fuse do you need for gentron generator?
Depends on the output of the generator
How do you know if you've torqued it down enough?
You'll need a torque wrench and the torque specifications for that bolt .
Does hydroelectricity need a generator?
no
How it is getting current from generator?
To draw current from a generator, you need to connect a load to it.
How do you re move the bolt from a western field m842a?
First you need to remove the stock, then behind the bolt is a plastic piece. There is a metal lever you pull down on it, after you pull it down pull the piece back while holding the lever. After the piece is removed open the bolt and pull it back.
How to drill out a metal bolt?
a good way to remove a metal bolt is to get a screw extractor. You drill a small pilot hole down the middle of the bolt, and lightly tap the extractor into the hole. The bolt will then twist out. You may need to add lube to the bolt if its rusted (WD-40 etc.)
Can a transformer be used to power a deep fridge from a generator?
You power "type" must match. Most likely your generator should be able to have the fridge plug directly in, but you may indeed need a transformer to step the voltage up or down.
Does an animal need a generator for regeneration?
No, they do not.
Generator Parts?
form_title= Generator Parts form_header= Fix a broken generator with new parts. What parts do you need for your generator? *= _[50] How old is your generator?*= _[50] Do you have a warranty for your generator?*= () Yes () No Would you like the parts delivered?*= () Yes () No
