0
How do you install pull chain switch into existing Fluorescent lamp?
Ljm686
Installing a pull chain switch into an existing fluorescent lamp includes both mechanical and electrical issues. One has to change the wires and the switch mounts to have the two be compatible within the same fixture.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Can a pull chain light switch be converted to wall switch?
The pull chain on the porcelain light fixture can be converted to a wall switch very easily. You will need to install a new two wire #14 cable from the box the fixture is mounted to now to the new wall switch box. Remove the power to the circuit by shutting that circuit's breaker off. The wire that is connected to the switch in the light fixture is the incoming "hot" wire. Disconnect it and re connect it to the black wire that goes down to the switch. Disconnect the white wire from the old porcelain fixture. For the installation of the porcelain fixture connect the white wire to the silver screw on the new fixture. Now connect the white wire that returns from the switch to the brass coloured screw on the new fixture. Mark this white wire with a small piece of black electrical tape to re identify it as not a neutral (code rule) but a potential "hot" wire. At the switch end make sure that the black wire is connected to the top screw and the re identified white wire (with a black tape marker) is connected to the bottom screw of the switch. Connect the ground wire in the cable to the new switch box and the existing fixture box. Install the switch making sure that the switch is in the off position and that the handle in facing downwards. Install switch plate cover, turn the breaker back on and you are finished. This project is relatively easy to do if there is already an existing wall box close to the pull-chain switch BUT ONLY if it already has the right wiring in it.If there is no such wall box then a new one will have to be installed and wired. If you already know how to do that safely you would not be asking this question here!For some relevant information, please see the related question below about replacing a wall switch by a pull switch. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
How do you wire in a pull chain switch in a bathroom light fixture?
If you are adding the pull chain to an existing fixture then the pull chain switch should have two wires. Wire nut either one to the hot wire coming in and the other to the black wire of the fixture.
How do you hook up one light to one switch in a basement lighting system that has all 10 lights connected to one switch?
If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.
How do you wire a light with a switch to another light with a switch in a different room?
Run the power line to a light box in each room, then drop a switch leg from each light box. The power line should daisy-chain to each box, with a "tap" off for the lights of each room. If you do not have experience with lighting or switch logic, it would be much more safe for you to contract with a qualified electrician.
Garage door motor hums but does not open?
It's probaly not latched on to the chain. Check to see if the chain is moving then check the connection to the chain.
Can you connect a wall switch and a light fixture to an existing light fixture?
If the question is, can I wire a switch to an existing light fixture (and I must assume that it's something like a pull-chain light fixture), the answer is yes.If the question is, "how do I wire a switch to an existing light fixture that has no external switch", the answer is, "in series".The attached web site gives simple instructions on how to wire a basic light switch to an existing light.See sources and related links below
How do you wire a pull switch on a hard wire ceiling light that has no switch?
Two options. Change the fixture to a keyed pull-chain, or add a pull-chain adapter to the existing fixture. Both available from Home Depot and others for about $3.
How do you repair a pull chain switch on a fluorescent light?
Shut off the breaker that supplies the voltage to the fluorescent fixture. Wire the new pull chain switch in series with the black incoming wire and the black wire of the ballast. Turn the breaker back on and your switch will now control the off on operation of the light fixture.
Is it difficult to install a chain link fence?
I'd like to install a chain link fence around my property. Are they difficult to install?
How do you install a timing chain on a 1997 Chevy blazer?
how to install time chain cover on a1997 blazer
Can a pull chain light switch be converted to wall switch?
The pull chain on the porcelain light fixture can be converted to a wall switch very easily. You will need to install a new two wire #14 cable from the box the fixture is mounted to now to the new wall switch box. Remove the power to the circuit by shutting that circuit's breaker off. The wire that is connected to the switch in the light fixture is the incoming "hot" wire. Disconnect it and re connect it to the black wire that goes down to the switch. Disconnect the white wire from the old porcelain fixture. For the installation of the porcelain fixture connect the white wire to the silver screw on the new fixture. Now connect the white wire that returns from the switch to the brass coloured screw on the new fixture. Mark this white wire with a small piece of black electrical tape to re identify it as not a neutral (code rule) but a potential "hot" wire. At the switch end make sure that the black wire is connected to the top screw and the re identified white wire (with a black tape marker) is connected to the bottom screw of the switch. Connect the ground wire in the cable to the new switch box and the existing fixture box. Install the switch making sure that the switch is in the off position and that the handle in facing downwards. Install switch plate cover, turn the breaker back on and you are finished. This project is relatively easy to do if there is already an existing wall box close to the pull-chain switch BUT ONLY if it already has the right wiring in it.If there is no such wall box then a new one will have to be installed and wired. If you already know how to do that safely you would not be asking this question here!For some relevant information, please see the related question below about replacing a wall switch by a pull switch. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
How do you wire in a pull chain switch in a bathroom light fixture?
If you are adding the pull chain to an existing fixture then the pull chain switch should have two wires. Wire nut either one to the hot wire coming in and the other to the black wire of the fixture.
Where can fluorescent bulbs be found in bulk?
You can purchase fluorescent bulbs in bulk online at any hardware website. If you would like to purchase fluorescent bulbs in bulk locally you may visit your local hardware store, or larger chain hardware stores such as Home Depot.
What is chain switch?
Chain switch is an old term for identifying the chain or string that hung from light bulbs that illuminated rooms in homes of the past. Light bulb sockets equipped with a "chain switch" or pull line of metal beads and a string can still be purchased at local hardware stores.
How do you install a chain link fence on a hill?
The same way as you install it on a level area.
How do you install a chain lin fence?
To install a chain link fence, you need to first lay the concrete. From there, install the metal fencing links, and put them upright. You should also make sure they are straight.
How do you install timing chain on a 2005 jeep 2.4?
do i have a time chain in my jeep 2.4 2004
