0
Add your answer:
Earn +20 pts
Can a pull chain light switch be converted to wall switch?
The pull chain on the porcelain light fixture can be converted to a wall switch very easily. You will need to install a new two wire #14 cable from the box the fixture is mounted to now to the new wall switch box. Remove the power to the circuit by shutting that circuit's breaker off. The wire that is connected to the switch in the light fixture is the incoming "hot" wire. Disconnect it and re connect it to the black wire that goes down to the switch. Disconnect the white wire from the old porcelain fixture. For the installation of the porcelain fixture connect the white wire to the silver screw on the new fixture. Now connect the white wire that returns from the switch to the brass coloured screw on the new fixture. Mark this white wire with a small piece of black electrical tape to re identify it as not a neutral (code rule) but a potential "hot" wire. At the switch end make sure that the black wire is connected to the top screw and the re identified white wire (with a black tape marker) is connected to the bottom screw of the switch. Connect the ground wire in the cable to the new switch box and the existing fixture box. Install the switch making sure that the switch is in the off position and that the handle in facing downwards. Install switch plate cover, turn the breaker back on and you are finished. This project is relatively easy to do if there is already an existing wall box close to the pull-chain switch BUT ONLY if it already has the right wiring in it.If there is no such wall box then a new one will have to be installed and wired. If you already know how to do that safely you would not be asking this question here!For some relevant information, please see the related question below about replacing a wall switch by a pull switch. As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
How do you wire in a pull chain switch in a bathroom light fixture?
If you are adding the pull chain to an existing fixture then the pull chain switch should have two wires. Wire nut either one to the hot wire coming in and the other to the black wire of the fixture.
How do you hook up one light to one switch in a basement lighting system that has all 10 lights connected to one switch?
If you have good access to the wiring this is relatively easy to do. Each of the 10 lights is connected to another in parallel in a "daisy chain" fashion. Light 1 is connected to the switch, light 2 is connected to light 1, light 3 is connected to light 2 and so forth. Let's say it is light 5 that you wish to switch separately. You can first install the new switch by either adding a new box or modifying old switch box. There are two gang switches that will fit the form factor of a single switch. TURN OFF THE POWER TO SWITCH BOX. Using the same supply input at original switch, add a new black wire to the wire nut for input to original switch and connect this to the input of new switch. Then run a new wire to light 5 and connect black wire to the output of new switch. Connect all the white wires together in switch box and separately connect all bare wires together in switch box. Now at light 5 undo the black and white wire coming from the fixture, and reconnect the wire nuts so that there is a direct connection between light 4 and light 6. Do the same for the ground if present (bare wire). You now have the fixture wires hanging free. Now connect the black wire from new switch to the fixture black wire and white to white and you are done.
How do you wire a light with a switch to another light with a switch in a different room?
Run the power line to a light box in each room, then drop a switch leg from each light box. The power line should daisy-chain to each box, with a "tap" off for the lights of each room. If you do not have experience with lighting or switch logic, it would be much more safe for you to contract with a qualified electrician.
Garage door motor hums but does not open?
It's probaly not latched on to the chain. Check to see if the chain is moving then check the connection to the chain.
How can I install a chain switch for a ceiling fan?
To install a chain switch for a ceiling fan, first turn off the power to the fan at the circuit breaker. Remove the fan's light kit if necessary. Locate the existing switch housing and disconnect the wires. Connect the new chain switch following the manufacturer's instructions. Reassemble the fan and turn the power back on to test the switch.
How do you repair a pull chain switch on a fluorescent light?
To repair a pull chain switch on a fluorescent light, you will typically need to replace the switch with a new one. Start by turning off the power to the light fixture, then remove the old switch by disconnecting the wires and unscrewing it. Install the new switch by connecting the wires as per the manufacturer's instructions and screw it back into place. Test the new switch to ensure it is functioning properly before turning the power back on.
How do i convert a table lamp with a twist knob to a chain pull switch?
To convert a table lamp from a twist knob to a chain pull switch, you would need to first remove the twist knob switch mechanism. Next, install a chain pull switch in its place by wiring it to the lamp's existing electrical connections. Finally, attach a chain to the pull switch for easy operation of the lamp. It is important to ensure that the chain pull switch is compatible with the lamp's wattage and wiring.
How do you convert a standard light fixture into a pull-chain one?
To convert a standard light fixture into a pull-chain one, you will need to replace the existing switch with a pull-chain switch. First, turn off the power to the fixture. Then, remove the existing switch and connect the wires to the new pull-chain switch following the manufacturer's instructions. Install the new switch into the fixture and secure it in place before turning the power back on.
How do you wire a pull switch on a hard wire ceiling light that has no switch?
Two options. Change the fixture to a keyed pull-chain, or add a pull-chain adapter to the existing fixture. Both available from Home Depot and others for about $3.
Can you connect a wall switch and a light fixture to an existing light fixture?
Yes, you can connect a wall switch to an existing light fixture by running a new electrical wire from the switch to the fixture. This allows you to control the light fixture independently of the existing fixture. It is recommended to consult a licensed electrician to ensure proper wiring and installation for safety.
How do I replace a broken pull chain on a light fixture?
To replace a broken pull chain on a light fixture, you will need to turn off the power to the fixture, remove the old pull chain switch, and install a new one by connecting the wires according to the instructions provided with the new switch.
How can I replace a broken fan pull chain switch?
To replace a broken fan pull chain switch, first turn off the power to the fan. Remove the old switch by unscrewing the housing and disconnecting the wires. Install the new switch by connecting the wires and securing the housing. Turn the power back on and test the new switch to ensure it is working properly.
How can I replace a broken light pull chain in my ceiling fan?
To replace a broken light pull chain in your ceiling fan, you will need to turn off the power to the fan, remove the old pull chain switch, and install a new one by connecting the wires according to the instructions provided with the new switch.
How can I fix the pull chain on my ceiling fan light?
To fix the pull chain on your ceiling fan light, you can start by turning off the power to the fan. Then, remove the light fixture cover and locate the pull chain switch. You may need to replace the switch if it is broken or damaged. You can find a replacement switch at a hardware store and follow the instructions to install it. Be sure to turn the power back on and test the new switch to ensure it is working properly.
How can I replace a pull chain on a ceiling fan?
To replace a pull chain on a ceiling fan, you will need to turn off the power to the fan, remove the old pull chain switch, and install a new one by connecting the wires according to the instructions provided with the new switch. It is important to follow safety precautions and consult a professional if needed.
Is it difficult to install a chain link fence?
I'd like to install a chain link fence around my property. Are they difficult to install?
