0
Is there a distance limit for conduit runs between junction boxes?
Wiki User
∙ 11y ago
No, there is not a distance limit. Most prints have specified 200' and local jurisdictions may impose a limit. The largest fish tape I've ever bought was a 200' so unless I want to vacuum a 'mouse' through the pipe; I go with 200'.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What are the advantages and disadvantages of steel junction boxs?
There are no advantages or disadvantages over which type of junction box to be used on electrical wiring. As long as the junction box is of an approved type (CSA or UL approved). It is cost or location which dictates which boxes will be used. PVC boxes for home wiring are the cheapest. Aluminium or steel are usually used in rigid or EMT conduit systems. PVC again when the conduit system involves underground wiring. In large electrical installations it is the electrical engineer that states what the conduit system type is and what type of electrical junction boxes that must be used.
How many degrees of bend is allowed in a conduit between boxes?
The electrical code states that there will be no more that 4 quarter bends between junction boxes. Keep in mind when conduit bending that an offset of two 45 degree bends is classed as a 90 degree bend. Offsets between two junction boxes uses up two of the four 90 degree bends allowed.In a conduit run between J boxes the number of bends can not exceed 360 degrees.The electrical code allows four 90 degree bends between pull boxes.
How do you size a junction box?
There is no minimum height for junction boxes per NEC. Any use of a junction box that would be subjected to harsh conditions because of its height would have to be rated for the condition. Personally, in outdoor areas, I like to keep boxes at least 18" above grade in areas that get snow.
What is the maximum degrees bending for conduit?
its 180 degrees If you use the above answer the conduit will flatten and close off. The maximum degrees for a single bend in conduit is 90 degrees. Also code only allows four 90 degree bends in a conduit run between pull boxes.
Do you have to break the ground wire at a pull box and bond it to the box?
When you refer to a pull box you have to be talking about a conduit system. In a metallic system, no don't have to ground pull boxes. By the fact that it is a metallic system the conduit and associated boxes are already grounded by the connection to the distribution panel. In a PVC conduit system a ground wire has to be pulled so that the load device has a return ground wire to trip the breaker on a ground fault. Pull boxes in a PVC system don't have to be grounded just the last junction box at the load.
What are the advantages and disadvantages of steel junction boxs?
There are no advantages or disadvantages over which type of junction box to be used on electrical wiring. As long as the junction box is of an approved type (CSA or UL approved). It is cost or location which dictates which boxes will be used. PVC boxes for home wiring are the cheapest. Aluminium or steel are usually used in rigid or EMT conduit systems. PVC again when the conduit system involves underground wiring. In large electrical installations it is the electrical engineer that states what the conduit system type is and what type of electrical junction boxes that must be used.
How many degrees of bend is allowed in a conduit run between j-boxs?
The electrical code states that there will be no more that four quarter bends between junction boxes. Keep in mind when conduit bending that an offset of two 45 degree bends is classed as a 90 degree bend. Offsets between two junction boxes uses up two of the four 90 degree bends allowed. If in a conduit run, the limit of 90 degree bends is utilized, always pull in stranded wire to make the pull go easier.
How many degrees of bend is allowed in a conduit between boxes?
The electrical code states that there will be no more that 4 quarter bends between junction boxes. Keep in mind when conduit bending that an offset of two 45 degree bends is classed as a 90 degree bend. Offsets between two junction boxes uses up two of the four 90 degree bends allowed.In a conduit run between J boxes the number of bends can not exceed 360 degrees.The electrical code allows four 90 degree bends between pull boxes.
What is the function of connectors?
The connectors are those things that exotic
How do you size a junction box?
There is no minimum height for junction boxes per NEC. Any use of a junction box that would be subjected to harsh conditions because of its height would have to be rated for the condition. Personally, in outdoor areas, I like to keep boxes at least 18" above grade in areas that get snow.
How do you find a junction box?
If the system is a conduit system you usually push a fish tape down the pipe from a known location. Usually about 99% of the time the fish tape will get hung up in the junction box. This will give you a distance from a known location to start looking for the box. If it is a Romex or Loomex system your best bet is to get an electrician friend to look at the system and ask him how he would wire the circuit. This is one of the faults that DIYers tend to do, that being burying junction boxes in the walls. They don't know the fact that most fires start in junction boxes and that is why they have to be accessible.
Is it necessary to ground at all metal junction boxes when using metal conduit or cable?
In a completely metallic conduit system it is not necessary to ground each junction box as long as the metallic system has the grounding capacity rating larger than that of the over current device protecting the circuit. The code book states what size conduits are rated at, for grounding amperages.
What combinations of bends in a conduit run require the use of a pull box?
Code states no more that 4 - 90 degree bends in a conduit run between pull boxes.
What is a taps?
A tap splice is a splice that is made usually in a mid span of aerial feeder conductors. It is used to connect a home from a utility company's secondary service drop on the street where the span is between poles and it is not convenient to connect a mid span home to either pole. Tap splices are also made in underground services where the utility feeders are in conduit between junction boxes. Each home along the route has an underground conduit from the junction box to the homes meter base. In the junction box where the home service wires connect to the utility feeders, this splice is known as a tap splice.
What is the maximum cable length allowed between junction boxes and other access points?
100
What is the maximum degrees bending for conduit?
its 180 degrees If you use the above answer the conduit will flatten and close off. The maximum degrees for a single bend in conduit is 90 degrees. Also code only allows four 90 degree bends in a conduit run between pull boxes.
Do you have to break the ground wire at a pull box and bond it to the box?
When you refer to a pull box you have to be talking about a conduit system. In a metallic system, no don't have to ground pull boxes. By the fact that it is a metallic system the conduit and associated boxes are already grounded by the connection to the distribution panel. In a PVC conduit system a ground wire has to be pulled so that the load device has a return ground wire to trip the breaker on a ground fault. Pull boxes in a PVC system don't have to be grounded just the last junction box at the load.
