0
Want this question answered?
Be notified when an answer is posted
Add your answer:
Earn +20 pts
What gauge wire to use for a sub panel?
That would depend upon how many amps will be used in the sub-panel. For example, a 30-A subpanel would need a minimum of 10 AWG feeder conductors.
What is difference between to busbar and feeder?
The busbar is used as a conductor and is used as a connection between the parallel and the feeder. The feeder is the supply, and it handles the relays.
What size generator for 200 amp service?
Usually generators are not sized for the entire house load. At 200 Amps and 240 volts that would be a 48 KW generator. You can get by with less by just creating a transfer electric panel with critical circuits. You can probably get by with a 20 KW generator.
Can you put a 60amp breaker and a 50amp breaker on a 60amp subpanel just as long as they are not being used at the same time?
You can. Using these size breakers in a 60 amp sub panel might be pushing the limit for breaking the sub panels feeder breaker. The breaker feeding the sub panel will have to be no bigger than 60 amps because of the main bus bar capacity of the sub panel. It would be better to install a 100 amp sub panel and then there would be a bit of a buffer and you will have the ability to add additional small load circuits.
What is a noise generator used for?
A noise generator produces electrical signals in both audio and video format. These are used for troubleshooting purposes in signal circuits for amplifiers and televisions.
What gauge wire to use for a sub panel?
That would depend upon how many amps will be used in the sub-panel. For example, a 30-A subpanel would need a minimum of 10 AWG feeder conductors.
What is difference between to busbar and feeder?
The busbar is used as a conductor and is used as a connection between the parallel and the feeder. The feeder is the supply, and it handles the relays.
What is a bull feeder?
A bull feeder is a feeder that is used for bulls to eat out of, like a trough or feed bunk.
What is different between feeder breaker and motor breaker?
You have to be careful with terms in the electrical field, Example: Main Feeder Circuits will feed a Transformer for distribution and each of those main circuits might feed numbeous Motor control centers. However each of those circuits could be called a main feeder for the motor control center. Confusing. We have High Voltage Transmittion tansformered down for Distribution. So normally a Feeder Breaker will feed Main circuits that will be used for distribution. Example Your home panel will have a main feeder circuit to the whole panel and distribution breakers to you home.
What is back synchronization panel?
It is a device that synchronize the electrical current from an emergency generator and main utility. It is usually used to prevent blink when main utility power comes back. It synchronized both current and slowly moved the load from emergency generator to main utility and released the emergency generator from the load.
Can you attach a generator to your sub panel and back feed your house main panel I have a 125 amp breaker in the main that feeds the sub through 2 aught wire?
Yes but it has to be a synchronous generator like the ones used on the grid, and it has to be run up and phased before being connected. That is because all the generators on a grid run at the same speed and phase (the phase of an individual generator alters a little depending on the power flow from it).
Discuss why the damper winding are not used in turbo generator?
It is definitely used in a turbo-generator
What is the most used pattern generator on the Web?
The most used pattern generator on the web is the ADC Generator. Their patterns are used by the majority of computer makers and they have a good reputation.
How pulse generator is used in ic74154?
there is no pulse generator in a 74154
Are ghost Shrimp only used as feeder shrimp?
yes they are
What does automatic document feeder mean when sending a fax?
An automatic document feeder is generally used for faxing multiple pages at one time.
What type of device is used to convert the high voltage on a feeder line to a lower voltage that can be used on the plant floor?
To convert the high voltage on a feeder line to a lower voltage that can be used on the plant floor you use a transformer.
