It depends upon the length. 10 gauge is rated for 30 amps to about 100 ft. However if running longer than 100 feet, you should drop down a gauge to #8.
the poem is have a limit rhyme the limit rhyme is 8 plus
10
Cat 2 cable was rated at 4 or 16 mbps whereas cat 3 cable would be rated at 10 mbps. Since 10baseT networks with Ethernet ran at 10 mbps this meant that cat 2 cable would not be useable in those networks. The minimum category cable for those networks had to be at least a cat 3 cable.
yes , the limit is 1 hour and 20 minutes and 10 seconds.
no, because range is the difference of the highest limit and lowest limit,therefore 665-655 is equal to 10 and not 645..........
7.2kW shower = 32 Amp fuse = 6 mm2 cable size7.5kW shower = 40 Amp fuse = 10 mm2 cable size8.5kW shower = 40 Amp fuse = 10 mm2 cable size9.5kW shower = 40/45 Amp fuse = 10 mm2 cable size10.5kW shower = 45 Amp fuse = 16mm2 cable size
Electrical wire size is directly dependant on the load amperage that is connected to it. The higher the load amperage, the larger the cross sectional area of the wire needs to be. The connected amperage to a conductor is determined by a group of electrical experts and their results are then written into the latest addition of the electrical code book of the country in which you live.
#10 wire is used on a 30 amp service.
#10 cable is no good for 120 amps, you need #2 cable, and it can be used at a distance of 250 ft.
Yes, the amp rating is a measurement of the highest amp load it should carry. So a 15 amp appliance will work on a 20 amp socket but you wouldn't want to use a 20 amp appliance on a 15 amp socket.
If you have a electrical speedo you don't have a cable. Change the speed sensor in the trans.
The electrical code does not allow wires smaller that #2 to be paralleled to a connected load.
A 25mm sq electrical cable is equal to a #4 AWG conductor. A #4 copper conductor with an insulation factor of 75 and 90 degrees C is rated at 85 and 95 amps respectively.
If you are talking about splicing a 40 amp cook top into an existing 3C #10 30 amp circuit then the answer is no. An appliance with that load ampacity needs to have its own dedicated circuit. This would consist of 3C #8 wire cable fed from a two pole 40 amp breaker located in the distribution panel.
On the left front fender well in an electrical box. 10 amp fuse.
No. The two appliances usually have dedicated circuits. The range will have a two pole 40 amp breaker and be fed with a 3-C #8 copper cable. The dryer will have a 30 amp two pole breaker and be fed with a 3-C # 10 copper cable. As you can see by powering a 40 amp device from a 30 amp breaker, full operation of the range will trip the 30 amp breaker.
fuse panel jeep tj wrangler. #1 20 amp/park lights. #2 20 amp/stop lights. #3 10 amp/panel lights. #4 10 amp/door switch defeat. #5 10 amp/air bag. #6 20 amp/rear wiper. #7 10 amp/back up lights/rear window defrost/abs. #8 10 amp/hevac. #9 10 amp/air bag. #10 10 amp/instrument cluster. #11 10 amp/solenoids,DRL. #12 10 amp/power distribution relays,skim. #13 10 amp/turn signals. #14 20 amp/front wiper. #15 10 amp/radio. #16 /open. #17 10 amp/HBL switch. #18 15 amp/Acc,battery,optional. #19 20 AMP/Acc.switch. #20 20 amp/clutch interlock ignition.