0
EMT is electrical metallic tubing. In the electrical trade there are nominal sizes expressed as a standard size. To answer your question you must state the conduit size in either electrical terms or in standard size terms to get a conversion size.
For example standard size 1/2" EMT has an actual diameter size of 3/4" and the 1/2"EMT connector for the 1/2" EMT conduit needs a 7/8" hole.
Likewise with 3/4" EMT the actual outside diameter is 15/16" and the 3/4" EMT connector needs a 1-1/8" hole.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
What is the hole size required for a 2.5 conduit?
A trade size hole for a 2-1/2" EMT conduit connector, the hole needs to be 2-7/8" in diameter. A 3" rigid conduit can also use this size hole without the lock nuts falling into the hole.
What is the multiplier for 45 degree offset in conduit bending?
Back set for all conduit sizes is not the same. The greater the diameter of the conduit the length of back set increases. Without the diameter size of the conduit, an answer can not be given.
How many wires can you put in a conduit?
Depends on the size of the conduit and the size of the wire.Allowable Conduit Fill CapacitiesSize and Type Of Conduit #14 Wire #12 Wire #10 Wire 1/2" EMT 12 9 5 3/4" EMT 22 16 10 1" EMT 35 26 16 1 1/2" EMT 84 61 38 1/2" PVC 10 7 4 3/4" PVC 18 13 8 1" PVC 32 23 15 1 1/2" PVC 80 58 36
Which one is cheaper PVC conduit or emt conduit?
PVC is cheaper but is used differently. PVC is usually baried in ground and emt usually runs exposed. You can use PVC exposed if it is schedule 80 gray PVC electrical conduit. Schedule 40 is for under ground
Is it legal to support a conduit from another conduit of the same size?
No, the conduit has to be supported individually from a supportive structure. The spacing of the strapping is related to the size of the conduit.
What is the hole size required for a 2.5 conduit?
A trade size hole for a 2-1/2" EMT conduit connector, the hole needs to be 2-7/8" in diameter. A 3" rigid conduit can also use this size hole without the lock nuts falling into the hole.
Can 480 volt electric be run in emt conduit?
Yes 480 volt electric wiring can be run in emt conduit.
What is the multiplier for 45 degree offset in conduit bending?
Back set for all conduit sizes is not the same. The greater the diameter of the conduit the length of back set increases. Without the diameter size of the conduit, an answer can not be given.
How many number 12 THHN conductors are allowed in half inch EMT?
According to the 2005 NEC Annex C, table C.1 you are allowed nine #12 THHN conductors in a 1/2" trade size EMT conduit. If your conduit run is any length at all, you would be wise to increase the conduit size to 3/4". as pulling 9 #12's for any length in 1/2" EMT is very difficult.
What is the smallest size emt conduit that can be used with nineteen 10 gauge thwn wires?
1 1/2 inch
How many wires can you put in a conduit?
Depends on the size of the conduit and the size of the wire.Allowable Conduit Fill CapacitiesSize and Type Of Conduit #14 Wire #12 Wire #10 Wire 1/2" EMT 12 9 5 3/4" EMT 22 16 10 1" EMT 35 26 16 1 1/2" EMT 84 61 38 1/2" PVC 10 7 4 3/4" PVC 18 13 8 1" PVC 32 23 15 1 1/2" PVC 80 58 36
When exist a junction box EMT conduit must be supported with how many inches?
When exist a junction box EMT, conduit must be supported within 18 inches.
What size drill bit do you need for a piece of conduit?
Depends on the diameter of the conduit. Try for 1/4" larger diameter drill bit.
Is equipment ground required in EMT conduit?
Yes it should be grounded
How many markings should a rigid nonmetallic conduit have?
There will be at lease three and on some conduits additional information. There will be the manufacture's name, type of material the conduit is manufactured from and the diameter size of the conduit. For example Scepter PVC 100 mm (for American customers 4") conduit.
Is EMT called by it inside diameter or outside diameter?
inside
A hand-operated conduit bender with a shoe for bending 1-inch EMT can also be used to bend?
1/2 inch emt
