Devices are rated by voltage and amperage. If you have a source rated for 600 volts you can use a 250 volt device, but not vice versa.
It's the amps that are controlled by the breaker not the volts. You can have a 600 volt 15 amp breaker, you can have a 347 volt 15 amp breaker. The breaker will trip when you exceed 15 AMPS.
A 30 amp circuit on a 250 volt service could handle up to 7500 watts. That's if it's actually 250 volts coming in. You should check that with your meter.
No, a 250-Amp fuse would be much larger than a 25-amp fuse. A fuse is generally designed to have a thermal runaway and melt the connection when there is too much current for too long.
4 amp, 250 volt (ASC) is what the fuse says on my blender
Yes, a 20 amp 250 volt circuit is typically sufficient to power a kitchen stove. Most electric stoves require a 240 volt power supply, which can be provided by a 20 amp 250 volt circuit. However, it's always important to consult the specifications of the stove to ensure proper voltage and amperage requirements are met.
Yes. But if you don't know the answer to the question please hire a professional. The life you save may be your own.
No, that adaptor can not supply a 6 amp load because it's limited to 1 amp, most probably by the size of the prongs and/or the internal wiring.
Electrically yes it is safe but the pin configuration will be different.
Answer for USA, Canada and countries running a 60 Hz supply service.If they fit, which I doubt, yes, you can use 600 volt fuses in place of 250 volt fuses so long as the amp rating is correct.YOU CANNOT USE 250 VOLT FUSES IN PLACE OF 600 VOLT FUSES !!!You can use a fuse with a higher volt rating but not a smaller volt rating than the voltage applied to the circuit.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.
It's the amps that are controlled by the breaker not the volts. You can have a 600 volt 15 amp breaker, you can have a 347 volt 15 amp breaker. The breaker will trip when you exceed 15 AMPS.
A 30 amp circuit on a 250 volt service could handle up to 7500 watts. That's if it's actually 250 volts coming in. You should check that with your meter.
you get a transformer...
No, a 250-Amp fuse would be much larger than a 25-amp fuse. A fuse is generally designed to have a thermal runaway and melt the connection when there is too much current for too long.
4 amp, 250 volt (ASC) is what the fuse says on my blender
Yes, a 20 amp 250 volt circuit is typically sufficient to power a kitchen stove. Most electric stoves require a 240 volt power supply, which can be provided by a 20 amp 250 volt circuit. However, it's always important to consult the specifications of the stove to ensure proper voltage and amperage requirements are met.
You need a breaker rated for 10 amps and 250 volts. The breaker must also fit properly in your panel.
Amps * Volts = Watts Amps * 12 = 600 600/12 = Amps = 50 amps You would need a reserve capacity, so I'd go somewhere between 60 or 100 Amp rated transformer. Transformers are rated in volt-amps which is usually calculated the same as watts. But the term "watts" technically does not apply to transformers. So you need a 600 volt-amp transformer or, as Redbeard has suggested, you need an 800 or 1000 volt-amp transformer. That's a lot of amps for a 12 volt system so I recommend you double check your requirements. You will need a #2 gauge wire if your requirements are correct.