answersLogoWhite

0


Want this question answered?

Be notified when an answer is posted

Add your answer:

Earn +20 pts
Q: What is the rate of a reaction if the value of k is 0.1 A is 1 M and B is 2 M Rate kA2B2?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Continue Learning about Math & Arithmetic

What has the largest value of the constant k?

how does the rate law show how concentration changes after the rate of reaction


How do you differentiate between reaction rate and specific rate constant?

The reaction rate is the rate at which the moles of substance change that varies with both temperature and concentration of the reactants. The specific rate constant is a proportionality constant that will vary only with temperature.


What information does the rate constant given from the rate law?

it tells how much the reaction rate is affected by concentration


The value of k in a rate law?

K is known as the rate coefficient, or the rate constant. The value of k is particular, and varies from reaction to reaction. It is dependent on different factors such as temperature, pressure, concentration, solvent, presence of a catalyst, etc., and therefore a change in any of these gives you a new value for k. To determine the value of k, you must use the experimental data to determine if you have a zeroth order, first order, or second order reaction. As indicated by the equation below, you must also have the actual rate.Rate= k[A]m[B]n[C]pYour overall reaction order is given by the sum of the orders of reactant.If you have a zeroth order reaction overall, then k will be equal to the rate. So if the reactants are consumed at a rate of 1.00 mol/liter/sec, then your k has a value of 1.00 mol/liter/sec. This means that no matter how much of the species you add, a lot or just enough, you will not change the rate.If you have a first order reaction where the concentration of A, [A] (in mols/liter), is consumed at a rate of .004 mol/liter/sec, then k = [A]/.004 mol/liter/sec, as given by the above equation: You divide the rate by the concentrations of the reactants. The units for a first order reaction are sec-1 or 1/sec, because you are dividing moles per liter by moles per liter per second. So the concentration of this does matter. The concentration of the reactant is proportional to the rate of reaction.If you have a second order reaction, then the addition of a reactant will increase the rate of reaction by a square of the concentration of the reactant. This is because you are now dividing the rate of reaction by, for example, [HNO3]2. Remember the the previous variables m, n, or p are the experimentally determined order of reactant. So a second order reaction results in squaring the concentration. Hope that helps!


The plot below shows data from the table above Calculate the rate using the plot when the reaction uses 0.050 M hypochlorite ions Rate is equal to the slope of the tangent line when the reaction use?

The slope of the tangent line at .050M hypochlorite ions is .0032M/S. This rate is much lower than the rate calculated in part d. In general, the more concentrated a solution the higher the reaction rate because the concentration of hypochlorite ions is the same in both reactions this reaction must have a lower concentration of iodine ions than the reaction in part d.

Related questions

What has the largest value of the rate constant?

how does the rate law show how concentration changes after the rate of reaction


What is The order of reaction for which unit of rate and rate constant is same?

In a zero order overall process, the rate and rate constant will be the same. (Reaction order is an exponent, and if that exponent is "0" then the value is "1" and will cancel out.)


What has the largest value of the constant k?

how does the rate law show how concentration changes after the rate of reaction


What is relative rate constant?

The relative rate constant is a ratio of the rate constants of two reactions in a chemical reaction mechanism. It is used to determine the rate of reaction between different reactants in relation to each other.


What measures of how fast reaction occurs?

The measure is the rate of reaction.


What is the speed at which a reaction occurs called?

The chemical term is reaction rate.


What would happen to the rate of a reaction with rate law ratekNO2H2 if the concentratin of H2 were halved?

Since the reaction is first order with respect to H2, if the concentration of H2 were halved, the rate of the reaction would be halved. This can be seen by entering one for each value in the rate equation, then changing the value of [H2] to 1/2 while keeping the other values the same: The rate changes from 1 to 1/2.


What does the rate law use to determine the rate of reaction?

The rate of a reaction is calculated using the concentrations of reactants.


What is the rate of the of a reaction?

An expression relating the rate of a reaction to the rate constant and the concentrations of the reactants


What does the rate law use to determine the rate of a reaction?

The rate law uses the concentrations of reactants to determine the rate of a reaction. By experimentally determining the relationship between the rate of reaction and the concentrations of reactants, we can derive the rate law equation for that specific reaction.


What is the rate of a reaction if the value of k is 0.01 A is 2 M and B is 3 M Rate kA3B2?

The rate of the reaction is calculated using the rate equation: rate = k[A]^3[B]^2. Given k = 0.01, [A] = 2 M, and [B] = 3 M, the rate can be determined by substituting these values into the rate equation and solving for the rate.


What is the rate of a reaction if the value of k is A and B are each 2 M?

The rate of a reaction can be determined using the rate law expression, which involves the rate constant (k) and the concentrations of reactants (A and B). Without knowing the specific form of the rate law, we cannot calculate the rate based solely on the values of the concentrations A and B. Additional information about the rate law or the order of the reaction with respect to A and B would be needed.