Want this question answered?
how does the rate law show how concentration changes after the rate of reaction
The reaction rate is the rate at which the moles of substance change that varies with both temperature and concentration of the reactants. The specific rate constant is a proportionality constant that will vary only with temperature.
it tells how much the reaction rate is affected by concentration
K is known as the rate coefficient, or the rate constant. The value of k is particular, and varies from reaction to reaction. It is dependent on different factors such as temperature, pressure, concentration, solvent, presence of a catalyst, etc., and therefore a change in any of these gives you a new value for k. To determine the value of k, you must use the experimental data to determine if you have a zeroth order, first order, or second order reaction. As indicated by the equation below, you must also have the actual rate.Rate= k[A]m[B]n[C]pYour overall reaction order is given by the sum of the orders of reactant.If you have a zeroth order reaction overall, then k will be equal to the rate. So if the reactants are consumed at a rate of 1.00 mol/liter/sec, then your k has a value of 1.00 mol/liter/sec. This means that no matter how much of the species you add, a lot or just enough, you will not change the rate.If you have a first order reaction where the concentration of A, [A] (in mols/liter), is consumed at a rate of .004 mol/liter/sec, then k = [A]/.004 mol/liter/sec, as given by the above equation: You divide the rate by the concentrations of the reactants. The units for a first order reaction are sec-1 or 1/sec, because you are dividing moles per liter by moles per liter per second. So the concentration of this does matter. The concentration of the reactant is proportional to the rate of reaction.If you have a second order reaction, then the addition of a reactant will increase the rate of reaction by a square of the concentration of the reactant. This is because you are now dividing the rate of reaction by, for example, [HNO3]2. Remember the the previous variables m, n, or p are the experimentally determined order of reactant. So a second order reaction results in squaring the concentration. Hope that helps!
The slope of the tangent line at .050M hypochlorite ions is .0032M/S. This rate is much lower than the rate calculated in part d. In general, the more concentrated a solution the higher the reaction rate because the concentration of hypochlorite ions is the same in both reactions this reaction must have a lower concentration of iodine ions than the reaction in part d.
how does the rate law show how concentration changes after the rate of reaction
In a zero order overall process, the rate and rate constant will be the same. (Reaction order is an exponent, and if that exponent is "0" then the value is "1" and will cancel out.)
how does the rate law show how concentration changes after the rate of reaction
The relative rate constant is a ratio of the rate constants of two reactions in a chemical reaction mechanism. It is used to determine the rate of reaction between different reactants in relation to each other.
The measure is the rate of reaction.
The chemical term is reaction rate.
If the concentration of H2 were halved, the rate of the reaction would also be halved, assuming H2 is part of the rate-determining step. The rate law rate = k[NO2][H2] shows that the rate is directly proportional to the concentration of H2.
The rate of a reaction is calculated using the concentrations of reactants.
An expression relating the rate of a reaction to the rate constant and the concentrations of the reactants
The rate law uses the concentrations of reactants to determine the rate of a reaction. By experimentally determining the relationship between the rate of reaction and the concentrations of reactants, we can derive the rate law equation for that specific reaction.
The rate of the reaction is calculated using the rate equation: rate = k[A]^3[B]^2. Given k = 0.01, [A] = 2 M, and [B] = 3 M, the rate can be determined by substituting these values into the rate equation and solving for the rate.
The rate of a reaction can be determined using the rate law expression, which involves the rate constant (k) and the concentrations of reactants (A and B). Without knowing the specific form of the rate law, we cannot calculate the rate based solely on the values of the concentrations A and B. Additional information about the rate law or the order of the reaction with respect to A and B would be needed.