0
What is the remote switch wire for an ATX or BTX power switch connected to?
Wiki User
∙ 11y ago
motherboard
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
What does the ATX or BTX power supply the remote switch wire from the case must be connected to before power will come on?
motherboard
When using the remote for a Hunter fan-light the light will not turn on-off using the remote-it will turn on-off using the wall switch but the fan will turn on-off using the remote Any ideas?
The fan is wired to the house wrong. Typically the red switch wire in the ceiling box will be nutted off and not used when a remote is installed. Sounds like, in this case, the fan light wire (blue) was connected to the red switch wire in the ceiling box instead of being correctly connected to the remote unit at the fan.
How do you rewire a wall switch to control both ceiling fan and light. The switch currently furns the fan on and off but the light has to be controlled with a pull chain?
Open up the ceiling box and disconnect the blue wire coming from the light and connect it to the black wire coming from the fan. Be sure and put a wire nut on the wire where the light was connected before you removed it. The wall switch is controlling power to the wire where the fan is connected so when you connect the blue fan wire to that connection you will be sending power to both the fan and light from the wall switch.
Were do you connect the dimmer wire?
There should be two wires coming from the dimmer switch unless it is a 3-way dimmer. The wires should be labled line and load on a normal 2-way switch. The line load is connected to the incoming power wire. the load wire is then connected to the wire that goes to the fixture. If you area replacing an old two way switch, then it will hook up exactly the same as the original switch, except for the fact that you will have to connect the pigtail wires of the switch to the other wires that used to be under screw terminals. I hope this answered your question. Thanks, Ben M. There should be two wires coming from the dimmer switch unless it is a 3-way dimmer. The wires should be labled line and load on a normal 2-way switch. The line load is connected to the incoming power wire. the load wire is then connected to the wire that goes to the fixture. If you area replacing an old two way switch, then it will hook up exactly the same as the original switch, except for the fact that you will have to connect the pigtail wires of the switch to the other wires that used to be under screw terminals. I hope this answered your question. Thanks, Ben M.
Should neutral wire of lamp be connected to the 3amp or the 6 amp side of a canopy switch?
You should never switch the neutral wire. The neutral of the appliance should be connected directly to the neutral wire leading to the service panel neutral bar.
What does the ATX or BTX power supply the remote switch wire from the case must be connected to before power will come on?
motherboard
When using the remote for a Hunter fan-light the light will not turn on-off using the remote-it will turn on-off using the wall switch but the fan will turn on-off using the remote Any ideas?
The fan is wired to the house wrong. Typically the red switch wire in the ceiling box will be nutted off and not used when a remote is installed. Sounds like, in this case, the fan light wire (blue) was connected to the red switch wire in the ceiling box instead of being correctly connected to the remote unit at the fan.
Where is the power steering pressure switch do on a 2002 Toyota Camry?
The switch is sitting directly in the power steering pump, and can trace by locating the wire connected to it.
What happens to the coil of wire when someone presses the switch?
If the coil is connected to a circuit and the switch is closed then, provided there is a power source, the coil will become energized.
Do you need to hook up the remote wire on your car amp?
Yes a remote wire is necessary. You must wire the remote wire from the amp to and ignition source of power (a component which turns on when the ignition in the car is engaged.) i.e. the radio. The remote wire signals for the amp to power on.
Continuous power to radio when key is turned off and door is closed on my 2003 chevy. bad wire maybe?
Wire is fine. The guy who installed the radio connected the power wire to the wrong side of the key switch.
How do you rewire a wall switch to control both ceiling fan and light. The switch currently furns the fan on and off but the light has to be controlled with a pull chain?
Open up the ceiling box and disconnect the blue wire coming from the light and connect it to the black wire coming from the fan. Be sure and put a wire nut on the wire where the light was connected before you removed it. The wall switch is controlling power to the wire where the fan is connected so when you connect the blue fan wire to that connection you will be sending power to both the fan and light from the wall switch.
Will any live wire fit to your CD player?
The preferable power would be to find a power line that is connected through the ignition switch so that the radio will turn off when the switch is off.
Why after buying a new CD player when the radio is on would the subs work but when you put in CD the subs do not come on?
make sure amp remote wire is connected to p.cont wire and not power ant wire on the radio
How do you wire a 3 way switch?
You will actually need 2 3-way switches to control something from two locations. The first switch will receive the power, while the other will go directly to the load being controlled. The switch getting power will have the hot lead connected to the common terminal. The other switch will have its common terminal connected to the hot lead going to the load. Two "travellers" will be connected between the other terminals on the switches. They will be connected switch-to-switch. And don't forget that your neutral coming from the power feed will be connected to the load. Also don't forget to connect ground wires.
Where do you hook up remote wire when using stock CD player?
the remote wire only needs a power source for the amp to turn on, so if u have a looped cable running from the remote input on the amp to the front of the car with a switch and then back to the power cable on the amp u can control when the amp is on just by turning the switch on or off. otherwise u will have to figure out which cable on the back of the stereo is switched power, or which cable only supplies power when the car is running. and that would require a wiring diagram.
Which wire is remote wire on 99 Chevy van stereo?
If you are hooking up an amp, you have to run your own remote wire or branch off the antenna power wire.
