0
What is the value of a smith and Wesson 22 lr ctg 4 barrel serial on handle 20241 number inside cylinder 76168 with an H above the number and a 3 below the number?
Wiki User
∙ 13y ago
Add your answer:
Earn +20 pts
How do you determine radius of barrel vault ceiling?
Simple, it it is a true barrel simple find the measurement from inside to inside of your barrel and divide by 2. IF it is not a perfect half circl barrel or true barrel, simple find your chord (measurement inside to inside) and find your rise. Once you have these measurements you can use your diameter formula to figure the radius
How would you find the surface area of a cylinder with a cylinder bored out of it?
if the cylinder is on the inside, it would not affect the surface area. otherwise, subtract the part of the inside cylinder that touches the outside from the cylinder
What instrument measures the diameter inside the cylinder?
caliper
What is the volume of a cylinder when inside circumference is 12 feet and height is 8 feet?
The volume of a cylinder when the inside circumference is 12 feet and height is 8 feet is: 91.7 cubic feet.
How many sides on a cylinder?
Four the inside, outside, top, & bottom
What date was smith and Wesson 861885 manufactured what is the model?
model stamped inside cylinder housing near barrel.
Where is the model number of a Smith and Wesson 357 mag snub 2 in stainless barrel?
Look on frame inside the cylinder area to find the model number of a Smith and Wesson 357 mag snub 2 in stainless barrel
What model is the Smith and Wesson pistol weapon serial number 152816?
look inside cylinder well for model near rear of barrel in frame
How do you clean a smith and Wesson 38 cal revolver?
open the cylinder and make sure it is EMPTY. Then merely swab down the inside of the barrel with a gun cleaner solvent as well as the cylinder. clean bore and cylinder with clean patches, then apply light coat of gun oil to bore, cylinder and outside of gun. Gun stores sell pistol cleaning kits..............
Where is the model number at on a Smith and Wesson revolver?
Open the cylinder and look inside on the frame where the crane assembly rests.
How do you find model of a smith and Wesson 38 cal pistol with serial number 266372?
the model is stamped inside the cylinder housing
Dan Wesson 357 magmum ctg with a 2 barrel how can you tell if it will enterchange to different size barrels?
Dan Wessons have a nut inside the front of the barrel that has to be removed to remove the barrel shroud and barrel. Keep in mind that Dan Wesson barrels are two pieces, the barrel itself, which is just a rifled tube that is threaded on each end, and the outer shroud. Once the barrel nut is removed the shroud just slides off and the barrel can be unscrewed from the receiver. When you put another length barrel on the gun you just screw in the new longer or shorter barrel tube, slip the shroud in place and tighten the barrel nut to hold everything in place. There is a special wrench that is designed to remove and add the barrel nut. You also need to be careful and measure the gap between the cylinder and the force cone of the barrel. DW makes a gauge to adjust this properly. If the distance is too small the cylinder can bind as it turns. A too-large gap effects accuracy and can be a safety problem.
What is the approximate age and value of a Smith and Wesson with 38 SW Special CTG on the right hand side of the barrel?
Not enough information. A lot of S&W models fit that description. sales@countrygunsmith.net I found the serial number on mine by taking off the grip and looking at the bottom or the handle. And to find the model number, I opened the cylinder and looked just inside where it hinged open. Mine is a 10-5.
What is the Value of your Smith and Wesson 32 long Identifying features are H95076 on the butt and 717x1 on the inside when dropping cylinder?
25-125 usd
What does a barrel vault do?
A barrel vault is a structure that spans an open area. It is a ceiling that is like half of a cylinder. Take a soup can and cut it in half from the top to bottom, and then look inside. The shape is that of a barrel vault.
Where can you find more information on a Frank Wesson tip-up rifle made in the late 1800s?
It looks like pictures I have seen of a "Frank Wesson 1860 rifle" (at http://buffaloclassic.tripod.com/). The numbers "3236" are stamped inside the shaft of the stock where the barrel fits; the barrel is about 23.5 inches long and the stock is about 22 inches.
How do you find serial numbers for a gun?
They can usually be found on side of frame, the top of barrel, the bottom of the butt, and inside the frame of cylinder area.
