Do you need to find the outlet at a hardware store, electrical store or around your pool area? At your pool area - GFCI's can sometimes be found around the pool equipment pad. Sometimes they are located just off the deep end of the pool at the edge of the deck straight back from the pool light if your pool has a light. However these fixtures do not have any access to an outlet. It is usually just a GFCI fixture. GFCI's can sometimes be found in shrubbery surrounding the pool. You just have to hunt for it in those locations. And there are the instances where no GFCI is provided. There may also be a GFCI in the circuit breaker box but this one will not have an outlet. What is your need for an outlet? If you have a pool light that does not have a GFCI in the system you then need to call a qualified swimming pool electrician or a qualified pool tech to install one. There are special requirements for this application.K
Not if the GFCI breaker is supplying the circuit you are wanting to put the GFCI receptacle into.
Your question is a bit vague, but let's try a two part answer. If you have a GFCI breaker in an electric panel you should only have one connection at the breaker, but the breaker will protect all devices on the circuit. If you are talking about a GFCI outlet, they are equipped to extend the GFCI protection to other non-GFCI outlets by using the proper "output" connection on the GFCI.
Deoends on code you are governed by. In USA, a GFCI outlet or a circuit controlled by a GFCI circuit breaker would be required.
How far do u put a GFCI receptacle from water
the oulets yes the switches would be a no
2
Do you need to find the outlet at a hardware store, electrical store or around your pool area? At your pool area - GFCI's can sometimes be found around the pool equipment pad. Sometimes they are located just off the deep end of the pool at the edge of the deck straight back from the pool light if your pool has a light. However these fixtures do not have any access to an outlet. It is usually just a GFCI fixture. GFCI's can sometimes be found in shrubbery surrounding the pool. You just have to hunt for it in those locations. And there are the instances where no GFCI is provided. There may also be a GFCI in the circuit breaker box but this one will not have an outlet. What is your need for an outlet? If you have a pool light that does not have a GFCI in the system you then need to call a qualified swimming pool electrician or a qualified pool tech to install one. There are special requirements for this application.K
Not if the GFCI breaker is supplying the circuit you are wanting to put the GFCI receptacle into.
Yes, Electrical supply stores usually carry them
Yes you can. Lots of blow dryers have GFCI protection built in.
In a word NO, that will not cause either GFCI to trip. The correct term is GFCI (Ground Fault Circuit Interrupter)
my gfci trips when my christmas lights r on and it rains is the gfci bad or is this normal of a perfectly working gfci
light bulbs,outlets, compuetrs, hair dryer and usually things that are connected to outlets. (oulets are tehe white rectangular things where yu plug wires into,just so you know,)
GFCI Breakers are quite a bit more expensive than a GFCI outlet. More often than not a typical residence will need only a handful of GFCI outlets that combined together will be cheaper than a GFCI breaker. If you need to protect a series of outlets with GFCI protection you can simply connect the rest of the outlets on that same circuit downstream from the first outlet on the line and make that the GFCI. All you have to do is connect all the other outlets to the LOAD side of the GFCI outlet. If a GFCI fault occurs in any of the outlets down stream they will trip that very first GFCI plug you placed and keep you safe.
Your question is a bit vague, but let's try a two part answer. If you have a GFCI breaker in an electric panel you should only have one connection at the breaker, but the breaker will protect all devices on the circuit. If you are talking about a GFCI outlet, they are equipped to extend the GFCI protection to other non-GFCI outlets by using the proper "output" connection on the GFCI.
The trip time for a GFCI is from 15 to 30 milliseconds.