0
You can get the same pipe through Walker Exhaust. Walker states there is no available part number for the 1993 Suburban, but if you look under 1993 Full Size Blazer, it shows the y pipe number, 40295. The converter, is the same number in both vehicles, 15840. Hope this helps you.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
If and x equals -12 find y?
if y=1/4x and x=,find y
How do you add a second toilet to an existing drain?
All you have to do is add a "Y" pipe or Call a plumber
If y³3y plus 4x0 find y by implicit differentiation?
The problem is If y³−3y+4x=0, find y′ by implicit differentiation
How do you find x intercept and the meaning and y intercept?
solve the x and you find the y
How do i find percentages?
To find x as a percentage of y, calculate 100*x/y.
Where is the oxygen sensor located on a 1993 Chevy Suburban k1500?
Either before or after y pipe, or both, depends.
How can you remove a catalytic converter from a 1993 Chevy Cheyenne 1500 truck?
It is part of the y pipe and must be cut out to remove without taking the y pipe
What is the location of the oxygen sensors on a 1993 GMC sierra truck?
the O2 (oxygen) sensor on a 93 gmc is in the left down pipe of the exaust Y pipe
Can you install a 1997 Chevy Suburban 350 V8 engine into a 1997 Chevy C1500 that has a 305 V8 with no mods?
The only one I can think of is the exhaust Y-pipe may not fit from the 305 to the 350.
How do you change oxygen sensor in 2001 Chevy suburban?
It will should be located on the Y pipe of your exhaust between the engine and the catalytic converter.Just unplug the wire harness and then unscrew the sensor and then install new one.
Where do i find the oxygen sensor on a 92' dodge ramcharger 4x4?
look on the Y pipe on the exhaust right under the manifold
How many oxygen sensors are on a 1993 Isuzu Rodeo or Trooper V6 3.2?
It appears that the 1993 Isuzu 3.2L V6 engine has just one oxygen sensor. It's a 4-wire type, located at the exhaust Y-pipe outlet. == ==
How hard is it to put a aftermarket radio in a 1993 Chev cheyenne Also without replacing the Y pipe how do you replace the oxygen sensor if the pipe threads are gone?
There is a product called helicoil that is used to replace worn threads in metal. You will probably find it at an auto parts store. A muffler shop can replace the nut the O2 sensor screws into. A friend of mine has a shop and does it regularly.
Where is the oxygen sensor on 1991 Dodge Dakota 3.9?
It should be threaded into, either the exhaust manifold, or the exhaust downpipe between the catalytic converter and the exhaust manifolds. If it's between the y-pipe and the catalytic converter, there will only be one. If it's between the y-pipe and the manifolds, there will be two, one on each pipe. You may have to look from underneath the vehicle to find and access it.
How do you remove starter on 1991 GMC Suburban 4wd 350 There is a front drive shaft and a protrusion of the frame that will not allow the starter to drop down?
take the 6 nuts off each exhaust pipe (3 on each side) called exhaust y-pipe..(pain in the ass)!! lol... and u should get access to get it out..its the way they are designed...
Is There any horsepower difference between a Y-Pipe and H-Pipe with 40 series flowmaster?
A y pipe simply merges the two exhaust flows into a single tailpipe. The H refers to a piece of pipe installed between the two and before the y to equalize the flow in the two before they become one. No real horsepower gain to be made there.
Does a 1993 Chevrolet Blazer 4x4 5.7L's catalytic converter have donuts to connect to the exhaust manifold?
Yes on the exhaust manifolds but the cat should either be welded or bolted on after your Y pipe then goes to your cat!
