0
If you want to operate the conductors maximum capacity, the conductor needs the heat, that the amperage produces, to be dissipated. This is why in the electrical code book there are two amperage ratings. The first one is for a free air rating which allows for a high ampacity of the wire. The other rating is for three conductors in a conduit which confines the cooling capacity and so the ampacity rating of these wires is lowered. The same procedure is used in cable spacings in ladder tray networks.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
Why insulation is needed on current carrying conductors?
To prevent the wire from getting short circuited to ground or even to other wires.
What size conductors are needed to run a 400 foot residential underground electric service?
Need to know what size service is going to be installed at the end of the run.
Is three phase transmission line is example of bundle conductor?
'Bundled' conductors describe a line in which two or more conductors are supported from the same insulator chain. In the UK, 275-kV transmission lines typically use two conductors per line, and 400-kV transmission lines typically use four conductors per line. The purpose of bundling conductors is to spread the electric stress on the conductors (e.g. for four conductors, the same amount of electric flux will be 'shared' between the four conductors, rather than concentrated on the surface of one conductor).
Are the three conductors in a single phase 240v circuit considered to be in parallel?
If the three conductors are in a single cable they physically are positioned parallel in relationship to each other. True parallel conductors are combined to split the current. They have to be of equal length and size so that they split the load current between the two or three or four conductors. Conductors are paralleled so that multiple smaller conductors, which are easier to work with, can carry equally the total load current. To answer the question no, the three conductors in a 120/240 circuit are not considered to be in parallel. All three of these conductors could have a different current being carried by them depending on how the load is distributed.
Why are conductors important?
Orchestra conductors are important because they keep all the musician in sync and on time with each other. If you're referring to conductors of electricity, they're important because they let electricity flow.
What is the needed for doping?
To increase the conductivity of semi conductors
What size conductors are needed for 800 amp service?
500
Why is a plug made of conductors and insulators?
Because you need conductors to take electricity to where it is needed. You need insulators to stop it going where it shouldn't.
Are electrical conductors and insulators equally important for electricity?
Yes. You need both conductors and insulators to work with electricity. Conductors such as wires provide a path for electricity to move where it is needed and insulators prevent electricity from dissipating, from being where it is not supposed to be and where it can cause harm and damage.
What is different between electricity and electronic?
Electricity is the flow of electrons through a cable. Electronics is set of conductors and semi-conductors (again kind of cables) through which electrons flow in specific way, needed by the machine.
Why insulation is needed on current carrying conductors?
To prevent the wire from getting short circuited to ground or even to other wires.
What are conductors insulators and semi conductors and super conductors?
b
Are scissors conductors?
They are Conductors, not much for insulation though. Differences between conductors and insulators? Conductors let energy such as electricity .
Is it true that shield wires conductors located above the phase conductors protect the phase conductors against lightning?
Yes, but they're not 'phase' conductors, they're 'line' conductors.
If ther are more than conductors in the raceway the ampacity of the conductors must be derated?
Ampacity must be derated depending on the number of conductors and the ambient temperature. In the Canadian Electrical Code Table 5C denotes derating for the number of conductors. 1-3 conductors = 100% load 4-6 conductors = 80% 7-24 conductors = 70% 25-42 conductors = 60% 43 or more conductors = 50%
Are metale uaually conductors or insulators?
Metals are conductors.Metals are conductors.Metals are conductors.Metals are conductors.
Why do metal spoons heat up instead of expanding?
They are conductors of heat They are conductors of heat They are conductors of heat
