0
With 10-3 wire what wire goes where when hooking the wire to an enclosed disconnect switch?
Wiki User
∙ 15y ago
Black wire to gold screw terminal, white wire to silver screw terminal, ground wire to ground terminal. I am sorry, I can't even begin to answer this question. I don't what you are trying to do and I am positive you don't either. Call a pro, please...pkazsr
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
When wiring a wall switch which color wire goes on the common terminal screws?
A typical switch doesn't have a Common screw in the strictest sense, it just has two screws which are each side of the switch. You probably have a a 3-way switch. If you are hooking up a 3-way switch as a normal switch, then connect the Black (Hot) wire to the common and the load to the side of the switch that makes UP the on direction and DOWN is off and doesn't get connected. You can determine for sure if you have a 3-way switch because the word ON and OFF don't appear on the toggle.
Can you plug your natural gas furnace into a 120 volt receptacle?
The furnace can be but it is not a good idea. Safety code requires a disconnect switch outside the area where the furnace is situated. This switch is used for an emergency shut down in case something electrically goes wrong with the furnace. In modern homes these furnaces are wired to a dedicated 120 volt circuit from the distribution panel. From the panel, the circuit is routed to the safety switch. From the safety switch, the circuit then continues to the furnace load.
If your dimmer switch goes out will it make your lights not work?
Yes it can.
Why is a switch used in a electrical circuit?
A switch is necessary to be able to turn the electrical circuit on and off, otherwise it would stay "on" all the time, until either the source of power stops giving out power - like a battery which goes dead - or part of the circuit stops working, like a light bulb that fails to work after a long time or a that motor siezes-up, overheats and eventually burns out. Even if you just disconnect a wire from the source of power, you are doing the same thing as a switch.
Does the black wire go on the gold screw for a three way light switch?
That depends on where the other end of the wire goes.
Hi 01 Honda accord pass window goes down by itself help?
Defective passenger power window switch. It is stuck in the down position. Raise the window and immediately disconnect the switch until you can replace it.Defective passenger power window switch. It is stuck in the down position. Raise the window and immediately disconnect the switch until you can replace it.
What would cause an interior brake light to stay on in 1997 ford escort?
Check you brake fluid and the brake switch on the proportioning value. If the fluid level is ok then disconnect the switch to see if the light goes out. Also check the parking brake switch.
2000 Ford F-350 air conditioner goes in and out?
It has a leak and is low of refrigerant. Take it to a professional for repair and recharging. Not a DIY job. I had this problem and found that the wiring hooking to the clutch and the pressure switch were broke and intermittently connecting.
When wiring a wall switch which color wire goes on the common terminal screws?
A typical switch doesn't have a Common screw in the strictest sense, it just has two screws which are each side of the switch. You probably have a a 3-way switch. If you are hooking up a 3-way switch as a normal switch, then connect the Black (Hot) wire to the common and the load to the side of the switch that makes UP the on direction and DOWN is off and doesn't get connected. You can determine for sure if you have a 3-way switch because the word ON and OFF don't appear on the toggle.
If you increase the temperature of an enclosed gas what happens to the pressure?
It goes up.
How do you disconnect a light switch and outlet that are tied together?
If there is a black wire going from the outlet to the switch and the other side of the switch goes back to the outlet then just cut these wires and connect supply wire directly to outlet. If the supply goes to the switch first, disconnect from switch and connect the two wires with a wire-nut. Some situations only switch one of the two outlets in a duplex device. Do the same thing, but also replace the outlet since the strapping between both outlets has been removed.
What are switch legs?
When the neutral wire goes to the switch
What is the function of the switch in circuit?
A switch simply opens a circuit, stopping the flow of electricity. For example: a simple circuit would be two wires from a battery, one of which goes to a switch, and the other goes to a light bulb. A third wire goes from the other side of the switch to the other conductor of the light bulb. With the switch closed the circuit is complete and the light goes on. Open the switch and the circuit is broken and the light goes off.
What is the function of switch in the circuit?
A switch simply opens a circuit, stopping the flow of electricity. For example: a simple circuit would be two wires from a battery, one of which goes to a switch, and the other goes to a light bulb. A third wire goes from the other side of the switch to the other conductor of the light bulb. With the switch closed the circuit is complete and the light goes on. Open the switch and the circuit is broken and the light goes off.
Why would the heater wipers and lowbeams on a 1992 VW Jetta not work but when holding highbeams on everything works?
I had a similar problem with my Jetta. It turned out to be the ignition switch. It takes a little work to change it as the steering column has to come out to disconnect the ignition switch from the bottom of the tumbler( where the key goes in). i
No spark on 4hp Briggs no kill switch what does the wire that goes under the flywheel go to?
goes to kill switch
How do you change a climate control switch on a 98 jeep Cherokee xj?
1997-2001. Grasp the lower corners of the trim panel in the center of the dash that goes around the stereo and the climate controls. Gently pull out, and slightly up. Unscrew the switch panel. Disconnect the wires from the switches. Remove the switches.
