answersLogoWhite

0

Squares do not have diameters; circles have them. If you are referring to the diagonal of a square, then you would use Pythagorean's Theorem to determine the length of the diagonal. 'Square' the length of one side and multiply by 2, then take the square root of that number to get the length of the diagonal.

that is = under root( 2 s) where s= side

User Avatar

Wiki User

14y ago

What else can I help you with?

Related Questions

How do you find the diameter of a circle inside a square of 16mm?

If the circle inscribes the square, the diameter equals the square's side length. In this case, 16mm.


How do you find the length of a rectangular box with given width and diameter?

Subtract the square of the width from the diameter. The square root of that is the length.


How do you find the circuferance of a circle in a square?

If the circle touches each edge of the square then its diameter is the same as the side of the square and its circumference is pi times the diameter.


How do you find the area with diameter?

Diameter implies circle Divide diameter by two square it. Multiply it by pi (3.14159...)


How do you find the radius of a circle inside a square?

The same as half the side of the square, as the radius of the circle is half its diameter, and the diameter of the circle is equal to the side of the square.


How do you find the surface area of a cylinder when given the diameter?

half the diameter and then get the radius times pi and square it


Find the area of a circle with a diameter of 6?

The area of a circle with a diameter of 6 units is: 28.27 square units.


How do you find area if you know the diameter?

radius = diameter/2 area of a circle in square units = pi*radius2


What is the formula for area of a half circle but you don't have the radius?

If you have the diameter, then the formula for the area of a semi-circle is:(pi x (diameter/2)2)/2That is,Divide the diameter in two to find the radius (diameter/2)Square the radius (radius x radius)Multiply it by pi (3.1416)Divide the answer by two to find half the circle.Remember your units. The answer will be in square inches, or square centimeters or square somethings.


How do you find the area of a circle when you have the diameter?

Divide the diameter by 2 to get the radius then square the radius, and finally multiply by pie (3.14)


A circle has a radius of 15 Find the diameter and the area?

diameter = 30 units area = 225*pi square units


How do you find the area of a circles when you have the diameter?

Divide the diameter by 2 to get the radius then square the radius, and finally multiply by pie (3.14)

Trending Questions
What is screw clamp on vernier caliper? What kind of battery can be restored after discharge? How do you set timing on 88 ramcharger 318? What type of oil ring is slotted so that excess oil can pass through it? White smoke coming out of exhaust? Does the timing chain on a 2001 Buick Regal have a maintenance schedule? What is the best oil Pan sealer? Were do you buy air bag sensor Chevy blazer? Why does your Dodge 1500 v8 smell very gassy runs rough back fires through throttle body hardly runs after about five minutes of this and five gallons of gas later it runs like a new truck? When attempting to recharge a car battery what might cause the destruction of the good battery? What type of coolant should you use in a 2005 Chrysler 300C? How do you reset low tire pressure for 2011 ford e350? What grade of oil is needed for Ford Sport Trac in 2007? Can you use the ac delco pf47 instead of the pf47e? What are 3 advantages of a hydraulic clutch actuation system? Where is the fuel filter located and how do you replace it on a 2001 Chevy Cavalier? I have an early 90's sears x-cargo carrier model 300.72501 and I need the front clip that secures the two halves. Searsparts.com does not list this model anymore. Where can I find this part? How do you change low beam bulb on ml350? Where is the fuel filter located on a 1992 Lincoln Continental? Is six hours of labor correct for replacing upper and lower control arms spring perch coil spring insulators strut rod bushings end links and frame bushings on a 1968 Mustang?