0
What else can I help you with?
What gauge wire do you need for a 600w rms Subwoofer 1200w Peak?
8 gauge is very common and really all youll need but i prefer 4 gauge its alittle more spendy but its good. make sure the amp wire holders will fit 4 gauge if you go with that.
What gauge wire for service entrance in Wisconsin?
Depends on the size of the service. 100 amp service will require 3 gauge, 150 amp service will require 1/0 gauge, and 200 amp service will require 3/0 gauge.
Can you use 14 wire for a light off a 20 amp circuit?
Yes, in home wiring as long as it is protected by a 15 amp breaker. Remember this circuit will only handle 1800 watts and cannot be loaded to any more than 1440 watts. So if each light is 75 watts then the maximum you can install is 19.
What is the wire size required for 1800 watts for lamps?
14 gauge will handle it with a 15 amp breaker. If you use 12 gauge use a 20 amp breaker.
Is it safe to use 10 gauge wire on a 20 amp breaker for a microwave?
No, 10 gauge wire requires the use of a 30 amp breaker. A 20 amp breaker is only used on 12 gauge wire.
Which kind of wires will I need to hook up my Amp?
You'll need RCA style cables to connect from your headunit to the amp. You'll then need Speaker Wire to run from the outputs of the Amp to the speaker terminals. You'll also need a heavy gauge power wire. A wiring kit such as the StreetWires Power Station PSK04Ri 4-gauge amplifier wiring kit.
What gauge wire do you need for a 600w rms Subwoofer 1200w Peak?
8 gauge is very common and really all youll need but i prefer 4 gauge its alittle more spendy but its good. make sure the amp wire holders will fit 4 gauge if you go with that.
What is the recommended gauge for electrical wiring to handle a 100 amp load, specifically in terms of copper wire?
The recommended gauge for copper wire to handle a 100 amp load is typically 3 AWG (American Wire Gauge).
When you unplug the rear speakers in a car from your 4 channel amp and just power your sub will all the power from the amp go directly to the sub?
depends on the wiring check out Subwoofer Wiring Diagrams
What are the electrical requirements for a 30 amp electric range?
A 30 amp electric range typically requires a dedicated 240-volt circuit with a 30 amp breaker and 10-gauge wiring.
What wiring kit i use for Crunch drive v4300 watt1200 amp?
i would say a 4 gauge kit would be more then enough for it 8 gauge min...
What type of wiring should be used with a 20 amp circuit, specifically considering the keyword "Romex"?
For a 20 amp circuit, it is recommended to use 12-gauge Romex wiring. Romex is a brand of non-metallic sheathed cable commonly used for residential electrical wiring.
What is the appropriate wiring setup for a 30 amp breaker?
For a 30 amp breaker, the appropriate wiring setup is to use a wire gauge of 10 AWG for copper or 8 AWG for aluminum. This ensures that the wiring can safely handle the electrical load without overheating. It's important to follow the National Electrical Code and any local regulations when installing the wiring for a 30 amp breaker.
What is the amp rating of NM wire?
The ampacity or amp rating of all wire is rated by the size of the wire. NM (non-metallic sheathing) wire is no different. In household wiring 14 gauge wire must go on a 15 amp breaker/ 12 gauge goes on a 20 A and 10 gauge goes on a 30 Amp.
How can you connect a big 4 gauge power wire into your 350w amp?
use 4 gauge spade crimp connectors
Can you run 4 gauge from your B to Capacitor then 8 gauge from the cap to the amp?
Now I'm guessing that while you have a 4 gauge input on the cap, you only have an 8 gauge input on your amp. So to answer your question, yes you can, but you will not draw as much power through the 8 gauge as you would the 4. Remember that the capacitor should be located as close to the amp as you can get it.
What size gauge power wire do you need for a 4000 watt amp?
2 or 4
