0
Add your answer:
Earn +20 pts
Can you run a 110v heater on 220v circuit?
No.It'll overload and fail just about immediately.It's possible - but not recommended - to run two 110 v heaters in series from a 220v circuit.
How do you rewire a 400 watt metal halide shop light to run on 110?
400w is the power 110 is the voltage. Is your light using 110v already or 220v? Believe you are already running at 110 and u don't understand electrical terms. Perhaps you should call an electrician
How do you calculate the current converting 110V 5.5 A to 220V?
110 v 5.5 amps is 605 watts. If it is transformed, the power in watts stays the same (in principle), so the 220 system would run at 2.75 amps.
How can you supply 220v machine to 208v supply?
Most 220 volt equipment will work on 208 volt supply. If the machine has a resistive load then the watts output will be lower than if supplied from a 220 volt source. If it is a motor load you will find that the equipment may run a bit slower but most motors will take the lower voltage. If the machine is a plug in device, install the appropriate receptacle to match the pin configuration and plug it in. If it is a hard wire installation this should be done by a qualified person.
What gauge wire for 220v 60a underground run of 260 feet ocation South Georgia?
A #2 copper conductor will limit the voltage drop to 3% or less when supplying 60 amps for 260 feet on a 220 volt system.
What size wire required to run 5 amp 220v?
45
Can an American 240V dual phase dryer be converted to work in Korea with 240V single phase power?
you could possibly design a fix for it but it would be a lot of trouble. the American dryer has internal components that run off 110v and that 110v is available from the three wire 220v circuit in the typical usa residence. this is because of the third wire, the neutral. the Korean 220 would be 2 wire. you would have to go inside the dryer, add a 220/110 transformer and rewire the dryer so that the 110v loads come off that transformer. it would then no longer be ul listed and would have to be evaluated by the authority having jurisdiction in Korea and back here in the usa.
Can you convert a 220 dryer into a 110 dryer?
No, it is not possible to convert a 220V dryer to operate on 110V. The electrical components in the dryer are designed to work with a specific voltage, and changing this can damage the appliance and pose a safety risk. It is best to use the dryer with the appropriate voltage outlet.
How do you run a clothes dryer line to a fuse box that has glass fuses if there are 2 in the box that are not being used?
It is recommended to hire a licensed electrician to run a new circuit for the clothes dryer from the fuse box. The unused glass fuses may not be rated for the higher current draw of the dryer and could potentially be a fire hazard. The electrician will be able to assess the existing setup and provide a safe and proper solution.
Will a clothes dryer rated at 220V 60 HZ work in a country that uses 220V 50 HZ?
Probably .. the fan will run a bit slower and the motor will get a bit hotter the timer will change from 1 hr to 1.16 hours
How do you wire 220V with 2 black 1 white wire?
Your black wires are your hot wires. The white is your neutral or common. It would be best to run an equipment ground (green wire) too.
what kind of voltage converter do I Need To Run A Clothes Dryer When I Just Have Standard 110 voltage In My Home ?
A step down converter will convert the voltage from 220/230 volts to 110 volts. Converters are labeled to display their capabilities, such as "110V to 220V Converter". Read the instruction manual for your Clothes Dryer and sketch the plug. You'll want to know the voltage of the clothes dryer --- it'll likely be 220 V. You need to visit a major appliance dealer and ask to buy a step down converter after discussing the plug type and voltage found in the owner's manual.
Can you run a 110v heater on 220v circuit?
No.It'll overload and fail just about immediately.It's possible - but not recommended - to run two 110 v heaters in series from a 220v circuit.
How do you rewire a 400 watt metal halide shop light to run on 110?
400w is the power 110 is the voltage. Is your light using 110v already or 220v? Believe you are already running at 110 and u don't understand electrical terms. Perhaps you should call an electrician
What size wire and circuit breaker is needed for an electric oven 4 wires with rated load of 34.9 amps 220v that is about 100 foot run from the electrical panel?
That would be a 40 amp 220v circuit. Circuit breaker is 40 amps and wire is 8 awg. Should use solid copper wire. Follow oven installation instructions.
What size wire is required to run 40 amp 220v in Canada?
Number 8. Wire <<>> A #8 copper conductor with an insulation factor of 75 and 90 degrees C are both rated at 45 amps.
Can you use a 40amp breaker on your 220v welder with 12-3 wire?
No, it is not safe to use a 40-amp breaker on a 220V welder with 12-3 wire. The wire size should match the breaker size to prevent overheating and potential fire hazards. In this case, a 30-amp breaker should be used with 12-3 wire for a 220V welder.
