0
You need to first determine where wires go. If you Google 3 Way Switch you can get a diagram. Each switch has 3 contacts.. Think about a kids teeter totter. Each end represents a switch contact and the center is a common point. You connect the ends to either end on the 2nd switch. The common contact on one switch goes to supply power hot side and on the other switch the common point goes to the load. Then the neutral of supply connects to the load neutral and the supply ground connects to the ground of the load.
What else can I help you with?
How do you install a dimmer switch for multi fixtures where the original switch has 2 black wires and one red with no green?
This simple if you have two switches controlling a set of light you will need to buy a three way switch. A three way switch will have a place for three connection. Depending on what brand of switch you purchase the directions will be sightly different but most dimmer come with detailed directions and diagrams. When you by a dimmer you need to read what kind of load it is meant to control. They are built to control incandescent light, magnet low voltage lights or electronic lights.
I am removing a dimmer switch to put in a regular switch but there are two incoming hot wires what do i do?
The regular switch just connects in the circuit the same way as the dimmer switch came out. If the dimmer switch had its own wires the only difference will be is you will have to supply your own wires from the new switch to the existing connection. IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS. If you do this work yourself, always turn off the power at the breaker box/fuse panel BEFORE you attempt to do any work AND always use a meter or voltage indicatorto insure the circuit is, in fact, de-energized.
How do you install a 20 amp switch for well pump?
Black/White/Ground power in and the same out. Tie the incoming and outgoing white wires together under a yellow wire nut and push them back in the box. Tie the ground wires together under a green wire nut and connect the pigtail from those ground wires to the ground screw on the switch. Connect the 2 black wires you have left to the 2 screws on the switch. Doesn't matter which black wire you connect to which screw.
What two wires connect to the timer switch on a century 87423 battery charger?
The two wires which connect the timer switch on a Century 87423 battery charger are the red and black wires. The red goes to the positive connector while the black goes to the negative connector.
Your wall cooker socket wires are black green and red which is which?
Red - active, (commonly known as your live cable) Black - Neutral Green - Earth
How do I install a dimmer switch with 3 wires?
To install a dimmer switch with 3 wires, first turn off the power to the circuit. Connect the ground wire to the green screw on the dimmer switch. Connect the black wire to the wire labeled "hot" on the dimmer switch. Connect the red wire to the wire labeled "load" on the dimmer switch. Secure the wires with wire nuts and install the dimmer switch into the electrical box. Turn the power back on and test the dimmer switch.
How do I install a dimmer switch with 4 wires?
To install a dimmer switch with 4 wires, first turn off the power to the circuit. Connect the ground wire to the green screw on the dimmer switch. Connect the black wire to the black screw, the red wire to the red screw, and the white wire to the silver screw. Secure the wires with wire nuts and mount the dimmer switch into the electrical box. Turn the power back on and test the dimmer switch to ensure it is working properly.
How do I properly wire a Leviton dimmer switch?
To properly wire a Leviton dimmer switch, first turn off the power to the circuit. Connect the black wire from the dimmer to the hot wire in the electrical box, the green wire to the ground wire, and the red and white wires to the remaining wires in the box. Secure the connections with wire nuts and install the dimmer switch into the electrical box. Turn the power back on and test the dimmer switch to ensure it is working correctly.
How do I properly wire a Lutron dimmer switch?
To properly wire a Lutron dimmer switch, first turn off the power to the circuit. Connect the black wire from the dimmer to the hot wire in the electrical box, the green wire to the ground wire, and the red and white wires to the remaining wires in the box. Secure the connections with wire nuts and install the dimmer switch into the electrical box. Turn the power back on and test the dimmer switch to ensure it is working correctly.
How do I properly wire a three-way dimmer switch in my home?
To properly wire a three-way dimmer switch in your home, you will need to follow these steps: Turn off the power to the circuit at the breaker box. Remove the existing switch and identify the common wire, traveler wires, and ground wire. Connect the common wire to the black wire on the dimmer switch. Connect the traveler wires to the other two wires on the dimmer switch. Connect the ground wire to the green screw on the dimmer switch. Secure the dimmer switch in place and turn the power back on to test the dimmer. It is important to follow the manufacturer's instructions and consult a professional if you are unsure about any step in the process.
How do you properly wire a dimmer light switch?
To properly wire a dimmer light switch, first turn off the power to the circuit. Remove the old switch and connect the dimmer switch's wires to the corresponding wires in the electrical box. Typically, you'll connect the black wire to the hot wire, the green wire to the ground wire, and the red or white wire to the neutral wire. Secure the connections with wire nuts and then carefully tuck the wires back into the box before attaching the dimmer switch to the box. Finally, turn the power back on and test the dimmer switch to ensure it is working correctly.
How do you wire a dimmer switch?
To wire a dimmer switch, first turn off the power to the circuit. Remove the existing switch and disconnect the wires. Connect the dimmer switch wires to the corresponding wires in the wall box, following the manufacturer's instructions. Secure the dimmer switch in place and restore power to the circuit to test the dimmer switch.
How do you wire a dimmer switch to a light?
To wire a dimmer switch to a light, first turn off the power to the circuit. Remove the existing switch and connect the dimmer's wires to the corresponding wires in the electrical box. Typically, the black wire is connected to the hot wire, the green wire to the ground wire, and the red or white wire to the load wire. Secure the connections with wire nuts and install the dimmer switch into the electrical box. Turn the power back on and test the dimmer switch to ensure it is working properly.
How do I properly wire a 2-way dimmer switch in my home?
To properly wire a 2-way dimmer switch in your home, first turn off the power to the circuit at the breaker box. Remove the existing switch and connect the dimmer switch's wires to the corresponding wires in the wall. Typically, this involves connecting the black dimmer wire to the hot wire, the green wire to the ground wire, and the red or white wire to the load wire. Secure the connections with wire nuts and mount the dimmer switch in the wall box. Turn the power back on and test the dimmer switch to ensure it is working properly.
Dimmer switch that has one black wire connected to the left side and two black wires connected to the right side of the switch How do you connect these wires if you want to just install a regular flip?
Check the screws next to the wires and see what color they are if they are green, black, and red then do what i say next, if not you're screwd. just connect the red/black/green wires in the holes in the flip switch and be careful not to touch the wires just the protective covering and inert them they should auto lock in there...if not just screw them in.
How do I install a dimmer switch with only 2 wires?
To install a dimmer switch with only 2 wires, first turn off the power to the circuit. Connect the black wire from the dimmer switch to the hot wire in the wall box, and the other wire to the neutral wire or ground wire. Secure the connections with wire nuts and install the dimmer switch into the wall box. Turn the power back on and test the dimmer switch to ensure it is working properly.
How to wire a dimmer switch correctly?
To wire a dimmer switch correctly, first turn off the power to the circuit. Remove the old switch and connect the dimmer's wires to the corresponding wires in the wall box. Follow the dimmer switch's instructions for specific wiring details. Secure the dimmer switch in place and restore power to the circuit to test the dimmer's functionality.
