0
The 30/36/6.5 rule applies. 30" clearance side to side, 36" clearance in front of the panel, and at least 6.5' clearance in height. Now, saying that I would call the local inspector and see what he says. He has the last word and even though the national code does not specify any other requirements, best to let him tell you his requirements. IMO, the farther away from the sink the better.
Add your answer:
Earn +20 pts
How can you connect electric to food disposal having the wire under the sink without switch?
You must have a switch to turn the disposal on and off. If you are asking how to connect because you do not have a switch. Install the switch under the sink just above the door opening. You can buy disposals that turn on and off when you place the lid over the hole. InSinkerator makes one.
How far from a laundry tub faucet should you install an electric dryer outlet?
There is no requirement on the distance the dryer must be from a sink. Any 120 volt outlet must be GFCI protected if it is within 6 feet of a sink. There is no requirement for a 240 volt dryer outlet. I would not want the dryer right next to the sink and I would want the dryer to be on a 4 wire circuit and not a 3 wire circuit. Use common sense here.
Why there is no driver circuit needed between 8051 microcontroller and an optoisolater?
Are you referring to the original Intel 8051, or one of the many variants? The 8051 has weak internal pullups on the i/o pins, and can source only about 60 ua, but can sink 1.6 ma, still not much when it comes to driving the led in an opto. Some 8051-based dervatives can sink much more current. Atmel's 89C2051 for instance, can sink up to 20 ma per i/o pin. This can directly drive most optos.
Why the heat sink is always used in power electronics converters?
A heat-sink is needed to dissipate the wasted power without any undue temperature rise. The effectiveness of a heat sink is measured by the watts dissipated per degree of temperature rise.
What is the difference between source driver and sink driver?
A source driver applies voltage to a ground (common)-referenced load. A sink driver grounds one side of a load which is already connected to the supply voltage. Given the same family of drivers, sink drivers generally have the greater current drive capability of the two.
How close can a sink be to a electrical panel?
There should be a minimum distance of 36 inches between a sink and an electrical panel to reduce the risk of electric shock or water damage. This spacing is typically required by building codes to ensure safety and accessibility for maintenance work on the electrical panel.
Is a clearance under the bathroom sink required for ADA code?
yes
The heat sink removes heat from the?
electric component
A microwave is halfway between the stove and sink and an electric can opener is halfway between the fridge and sink?
So.... what exactly is the QUESTION !
How much mls fill a kitchen sink?
How big is the kitchen sink
Why does a toaster sink?
Sink in what water? Well, not taking in account that the electric wires in the toaster shouldn't be immersed in water, a toaster would sink because its density is greater that of water. Had it been less the toaster would float.
How much does it cost to install a sink?
Maybe 600 for a kitchen sink to be installed.
Does a bath towel sink or float?
it sometime sink if it has tu much water but yes it floats
Is a sink an appliance?
No, a sink is not considered an appliance. It is a plumbing fixture used for washing dishes, hands, and other purposes in the kitchen or bathroom. Appliances are typically devices that perform specific functions and are powered by electricity or gas.
How do you pull a dent from a Polo without removing the door panel?
Well, you could try one of those plungers for unblocking a sink.
What is the minimum distance by code that the front of a toilet has to be from a sink?
As long as they're not easily confused, it is mostly a matter of choice.
Which is more efficient efficiency of carnot engine increased by increasing temp of source or decreasing temp of sink?
That depends how much you increase the source, and how much you decrease the sink.That depends how much you increase the source, and how much you decrease the sink.That depends how much you increase the source, and how much you decrease the sink.That depends how much you increase the source, and how much you decrease the sink.
