answersLogoWhite

0


Best Answer

Answer for USA, Canada and countries running a 60 Hz supply service.

The NEC has more than one table that can be used for this determination. The necessary parameters include the intended purpose of the motor, the name-plate current rating (that's not the locked rotor rating) and the duty rating of the motor. All this information should be listed on the name plate.

<><><>

As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.

Before you do any work yourself,

on electrical circuits, equipment or appliances,

always use a test meter to ensure the circuit is, in fact, de-energized.

IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOB

SAFELY AND COMPETENTLY

REFER THIS WORK TO QUALIFIED PROFESSIONALS.

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How size cable base on locked rotor amps?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How does a cable backhoe excavator work not cable front shovel or face shovel?

The operating parts consist of a boom, hinged at its base end at the machine, and a stick, pivoting on the outer end of the boom. The stick extends above and below its pivot point, with the digging bucket on the lower end and the retracting cable at its upper end. A second cable, the digging cable, is attached to the lower end of the stick, near the bucket. The digging and retraction actions of the cables is straightforward. To lift the boom/stick/bucket assembly, the digging cable is locked and the retraction cable is pulled in. With the digging cable locked, the boom and stick assembly becomes a ridged triangle and is forced to move up as the retracting cable is shortened. After the bucket is raised, the boom is pivoted to the dump site, the retraction cable is locked and the digging cable is allowed to play out. The Retracting cable holds the boom and stick assembly in its elevated position and its weight forces the stick and bucket outward until the load is dumped.


Location camshaft sensor 350 5.7?

inside the distributor underneath the rotor cap. You must line up rotor base to the proper location to remove cam sensor.


What should be amps for an alternator for 2001 Chevy Surburban?

The standard alternator amperage on all 2001 Suburbans is 130 amps. The base, stripped-down Suburban with little or no options had and alternator output of 105 amps, but there were not many of those.


A cable is attached to the top of an 80' pole and to a stake in the ground 35' from the base of the pole What angle will the cable and the ground form?

66


A cable is attached to the top of an 80 pole and to a stake in the ground 35 from the base of the pole what angle will the cable and the ground form?

66


How do you replace a broken shift cable?

Loosen the shifter cable not on each end of the shifter cable. The shifter cable will come off. Reverse the process to install the new shifter cable.


Which companies make cable descramblers?

Companies that make cable descramblers include the company API and the company Base OPS. You can also find cable descramblers online in stores such as Amazon.


Which cable is necessary to support 100 meter for 10G Base-t?

CAT6a


Is the Cable Cat 6 available in 20 meters?

The Cable Cat 6 is an Ethernet cable that supports fast Ethernet 10G BASE-T. This cable is available in a 20 meter length online from various retailers including cabling4less.


What are the cable TV rates, for minimum channels, for time warner cable?

Without specifics of where you live, this question is best answered by your cable company. Rates vary depending on where you are that they base the rate on your zip code.


What utp cable category is recommended as 100 base T media?

Cat 5


What is mA vs Amps?

mA stands for milliamps, which is a unit of electric current equal to one-thousandth of an ampere. Amps, on the other hand, refers to amperes, which is the base unit of electric current in the International System of Units. So, 1 mA is equal to 0.001 amps.